TenTec
[Top] [All Lists]

Re: [TenTec] Orion Mic Woes - Sounds like RFI but Wasn't

To: <tentec@contesting.com>
Subject: Re: [TenTec] Orion Mic Woes - Sounds like RFI but Wasn't
From: "Don Steele" <dsteele@IowaTelecom.net>
Reply-to: Don Steele <dsteele@IowaTelecom.net>, tentec@contesting.com
Date: Thu, 23 Dec 2004 12:57:16 -0600
List-post: <mailto:tentec@contesting.com>
To the group, I have been using a Heil Pro Set with the Heil mike adaptor(I can't remember the part number)as my only mike since purchasing the Orion.I have never experienced this problem in over 2000 QSO's with the radio.I am no expert,but that leads me to believe the problem does not lie with the mike,or wiring.

Don
NT0F
----- Original Message ----- From: "Tom Wagner" <tfwagner@snet.net>
To: <tentec@contesting.com>
Sent: Thursday, December 23, 2004 7:10 AM
Subject: RE: [TenTec] Orion Mic Woes - Sounds like RFI but Wasn't



I failed to point out that this is using a stock Heil
Proset which has only one wire plus a shield to the mic.

I'm sure with a two-wire + shield situation that grounding
the shield is the proper approach

73,
Tom

-----Original Message-----
From: tentec-bounces@contesting.com
[mailto:tentec-bounces@contesting.com]On Behalf Of Tom Wagner
Sent: Thursday, December 23, 2004 8:08 AM
To: tentec@contesting.com
Subject: RE: [TenTec] Orion Mic Woes - Sounds like RFI but Wasn't


I tried connecting the shield to the mic connector and the RFI-like noise was worse than ever. My Orion shows 1/2 ohm resistance between the mic connector and the rear ground lug.

73,
Tom

-----Original Message-----
From: tentec-bounces@contesting.com
[mailto:tentec-bounces@contesting.com]On Behalf Of N0KHQ@aol.com
Sent: Sunday, December 19, 2004 7:42 PM
To: tfwagner@snet.net; tentec@contesting.com
Subject: Re: [TenTec] Orion Mic Woes - Sounds like RFI but Wasn't


Hi Tom and Group,


If you want to know if you have the later version of the Orion, take a
multi-meter and set it to OHMS. One lead will go to the Orion mic connector,
the
other lead will go to the ground wing nut on the back of the Orion. If the
meter shows a direct SHORT, you have the later version (this is because the
Orion
mic connector is chassis grounded). If the meter shows an OPEN or any
resistance at all you have the earlier version. (Orion mic connector not
chassis
grounded).


Assuming Orion later version: (Orion mic connector grounded to chassis)

There should be 2 wires coming off of the mic Element. Possibly white and
(red or black). If you look real, real close at where the wires are soldered
to
the element you may see a + sign and a - sign. Maybe! If not, I would
choose
the white wire as being the Audio hot lead (+ send) and the other wire
would
be the Audio ground lead (- return)


If I were you, I would purchase some good quality mic cable. This cable
will
have 2 wires (usually white and red) that are surrounded by a shield wire.
Additional wires may be in the cable but they will be by them selves (not
wrapped within the shield) these wires can be used for PTT or whatever).
Heil
sells excellent mic cable, very well shielded.


The shield of the cable connects between the mic housing case and the mic
connector on the other end of the mic cable. Thats all it does.

One of the wires that is surrounded by the mic cable shield wire will
become
the audio hot lead + (send) usually white, the other wire will be the audio
ground lead - (return) usually red.


The Audio + lead (white (send)) will go to Pin #1 on the Orion, the Audio -
lead (red (return)) will go to Pin #2 on the Orion. PTT wire (PTT grounds
to
chassis) (1 wire only) will go to Pin #3 on the Orion. Inside your mic PTT
switch you may have to run a wire from there to the mic housing shield.


Or

You can send your Audio in through the rear of the Orion like I do at line
level and say "to hell with the Orion mic connector". There are 3 ways to
key
the Orion, 1 is through the rear of the rig. The other is a 1/4" mono phone
plug inserted into the "CW" on the front of the Orion (requires a Menu
change)
and 3rd is to use the mic PTT Pin #3.


You have a whole lot of choices, just choose the right one for you.

Happy Holidays.

John / N0KHQ
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec


_______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec


_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>