TenTec
[Top] [All Lists]

Re: [TenTec] D 104 and Argonaut V

To: gsm@mendelson.com,Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] D 104 and Argonaut V
From: Robert & Linda McGraw K4TAX <RMcGraw@Blomand.Net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Tue, 27 Dec 2005 12:49:00 -0600
List-post: <mailto:tentec@contesting.com>
The G-Stands which have the internal base mounted amplifier does require a 
9V battery installed in the base.  The PTT bar on the side has contacts that 
are used to turn the amp in the base on and off.  There is, to my knowledge, 
no provision for powering the amp from an external source.  Do note that the 
switching arrangement on the PTT bar switch does provide a make before break 
set of contacts.  These should be used to switch the DC for the amp thus 
preventing a small thump when switching.  The other set of contacts should 
ground the input of the amp thus preventing the pop associated with the 
switching.  To confirm correct wiring, if you squeeze the bar slowly the 
transmit should be activated before the audio is activated. As you release 
the bar slowly, the audio should stop before the PTT releases the 
transmitter.

As to the 2 wire mike cable,  be it coiled or straight, white is audio, 
shield is shield/ground, and black is PTT.  This is unless someone has 
replace it with something else.  Anyway, remove the 3 screws that hold the 
bottom cover on.  There you will find a terminal strip to which all 
connections can be made.  And there should be a schematic attached to the 
bottom plate on the inside.

While the pot is accessible through the hole in the base plate,  normally 
about 50% will work in most all applications.  Turn it fully clockwise and 
note the position, turn it fully counterclockwise and note the position and 
then set it about 1/2 way in between the two.  Counterclockwise is least as 
long as some diligent sole hasn't changed things.

If you need a schematic, let me know and I'll scan mine and send you a JPG. 
Or it may be on the internet, I haven't looked.

73
Bob, K4TAX


----- Original Message ----- 
From: "Geoffrey S Mendelson" <gsm@mendelson.com>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Tuesday, December 27, 2005 12:08 PM
Subject: Re: [TenTec] D 104 and Argonaut V


> On Tue, Dec 27, 2005 at 09:56:02AM -0800, William wrote:
>> My son gave me a nice D 104 Silver Eagle, the one with the pre amp-I am
>> guessing since it has the standard mic cable, a two wire cable which I
>> assume is for powering the amp and a small switch on one side.
>
> I've never seen one of those. The amplified D-104s that I have use an 
> internal
> 9 volt battery. I assume that someone decided that they did not want to
> rely on a battery and added a power cable and switch.
>
> I'm not sure of the specs for power, but many people with Kenwood 
> transcivers
> that supply 8 volts use that for their D-104s. I did not, I just used the
> internal 9 volt battery. Since they are over $5.00 each here, I may just
> do it next time I need to replace the battery on one of my amplified 
> stands.
>
>> I would like to use this with my Argonaut V and need to know what voltage
>> should be supplied and any recommendations on setting the gain via the 
>> small
>> pot in the base.
>
> Start in the middle and and adjust the mic gain and and the pot until it
> sounds good. Or if you prefer, leave the mic gain where it always is, 
> start
> at the lowest setting for the pot and increase it until you get what you
> want.
>
> It depends upon whether you plan on switching mics and how often.
>
> Geoff.
> -- 
> Geoffrey S. Mendelson, Jerusalem, Israel gsm@mendelson.com  N3OWJ/4X1GM
> IL Voice: (07)-7424-1667  IL Fax: 972-2-648-1443 U.S. Voice: 
> 1-215-821-1838
> The trouble with being a futurist is that when people get around to 
> believing
> you, it's too late. We lost. Google 2,000,000:Hams 0.
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec 


_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>