TenTec
[Top] [All Lists]

Re: [TenTec] [Orion] Orion II Noise Blankers

To: Ron Castro <ronc@sonic.net>,Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] [Orion] Orion II Noise Blankers
From: John Nason / NA9U <na9u@arrl.net>
Reply-to: na9u@arrl.net,Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Sun, 26 Feb 2006 06:19:50 -0800 (PST)
List-post: <mailto:tentec@contesting.com>
Classically, noise blankers were intended to remove
ignition noise which is short pulse, short duration,
high frequency.  

John

--- Ron Castro <ronc@sonic.net> wrote:

> Great test, Lin!  This confirms my more subjective
> observation that both the 
> HW and SW NB's work extremely will on short-duration
> peak noise.  Probably 
> the stronger and shorter the peak, the better it
> works.  Greater pulse-width 
> duration noise, such as that from arcing power line
> insulators is another 
> story...
> 
> Ron N6AHA
> 
> ----- Original Message ----- 
> From: "Lin Davis" <linbdavis@earthlink.net>
> To: "Discussion of Ten-Tec Equipment"
> <tentec@contesting.com>
> Sent: Saturday, February 25, 2006 2:34 PM
> Subject: Re: [TenTec] [Orion] Orion II Noise
> Blankers
> 
> 
> > After reading some some of the comments about the
> O2 noise blankers, I did 
> > this
> > test:
> >
> > O2 settings:
> > AGC: slow (Hang: 2.02 sec, Decay: 5dB/s,
> Threshold: 0.37uV)
> > F= 21.3MHz, USB, BW=2100hz, PreAmp OFF, Atten:
> none.
> > Antenna: 10 foot piece of wire in ANT2 and within
> three feet of noise 
> > source.
> >
> > I used a soldering iron for the noise source by
> switching it on and off 
> > about 30
> > times for each of the settings below and recorded
> the highest S-meter 
> > value
> > observed. (Probably not too good for the iron ;) )
> >
> > Results:
> >
> >    NB       S-METER    Equiv. Input  Total
> > HW   SW                Power (dBm)   Reduction
> (dB)
> >
> > OFF  OFF    S9+55          -31       0
> > OFF  1      S9+30          -52       21
> > OFF  5      S9+20          -59       28
> > OFF  9      S9+20          -59       28
> > ON   OFF    S1.5           -94       63
> > ON   1      No Movement    LT -101   GT 70
> > ON   5      No Movement    LT -101   GT 70
> > ON   9      No Movement    LT -101   GT 70
> >
> > Where:
> > LT = Less Than
> > GT = Greater Than
> >
> > The Equivalent Input Power values came from my
> S-meter calibration I did a 
> > while
> > back with a precise RF generator (Agilent aka HP)
> >
> > Conclusion:
> > For this type of noise, the hardware blanker is
> very effective! The DSP 
> > blanker
> > is less effective, but does reduce it
> signifigantly. Remember, a reduction 
> > of
> > 70dB means the equivalent power was reduced by a
> factor of 10,000,000.
> >
> > I hope you found this informative....
> >
> > 73,
> > Lin
> > WB1AIW
> >
> >
> > Ronald Gorski wrote:
> >> At 03:55 PM 2/24/06 -0500, BobK8IA@aol.com wrote:
> >>
> >>
> >>>Both the hardware and software noise blankers in
> the Orion II dont  seem 
> >>>to
> >>>be doing much, if anything. The digital NR
> certainly operates as I can 
> >>>hear
> >>>that one kick in.
> >>>
> >>>I did a master reset and no difference.
> >>>
> >>>Anyone else notice my problem?
> >>>
> >>>73, Bob  K8IA
> >>>
> >>>_
> >>
> >> For me, the hardware NB works somewhat but the
> s/w NB does nothing. As I
> >> mentioned in a previous thread, the NR produces
> audio distortion.
> >> Ron N9AU
> >>
> >>
> >>
> >>
> >>>______________________________________________
> >>>Orion mailing list
> >>>Orion@contesting.com
>
>>>http://lists.contesting.com/mailman/listinfo/orion
> >>
> >>
> >>
> >>
> >> _______________________________________________
> >> TenTec mailing list
> >> TenTec@contesting.com
> >>
> http://lists.contesting.com/mailman/listinfo/tentec
> >>
> >>
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> >
> http://lists.contesting.com/mailman/listinfo/tentec
> >
> > 
> 
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> 

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>