Ah! Thanks!
Bernie K5XS
-----Original Message-----
From: n4py@arrl.net
To: tentec@contesting.com
Sent: Mon, 22 Jan 2007 8:19 PM
Subject: Re: [TenTec] ORION Display (horizontal line??)
The horizontal lines just represent the maximum range the bandwidth
rectangles can move. The break in the line is just to separate the line for
the main receiver side and the sub receiver side. If you move the band
width to 6000 hertz and then move PBT through its entire range, you will see
what I mean.
Carl Moreschi N4PY
121 Little Bell Drive
Bell Mountain
Hays, NC 28635
----- Original Message -----
From: "Richard Williams" <richardw@mho.com>
To: <w1ael@arrl.net>; "Discussion of Ten-Tec Equipment"
<tentec@contesting.com>
Sent: Monday, January 22, 2007 8:47 PM
Subject: Re: [TenTec] ORION Display (horizontal line??)
> Allen,
>
> The way I read Bernie's question, he is asking about the thicker solid
line
> that is directly above the spectrum display. There is a "break" (it
> becomes a thin line) in it just between the "0" and the next number (.6,
> 1.2, 2.5, 5, or 10 - depending on the sweep range) to the left.
>
> I read it this way because Bernie says: "Immediately above the spectrum
> sweep scope is a horizontal line on which the rectangles representing the
> bandpasses for the main (left) and sub (right) receivers rest". The
> rectangles don't "rest" on the the horizontal line(s) above the filter
> bandwidth graphic; which you correctly defined in your response.
>
> Personally, I don't know what the break in the bar represents;
interesting
> question, do you happen to know the answer?
>
> Dick K8ZTT
>
>
> ----- Original Message -----
> From: "Allan H. Kaplan" <w1ael@arrl.net>
> To: <tentec@contesting.com>
> Sent: Monday, January 22, 2007 6:14 PM
> Subject: Re: [TenTec] ORION Display
>
>
> > The horizontal line above the filter bandwidth graphic represents the
> > bandwidth of the roofing filter in use at 9 MHz. The filter bandwidth
> > graphically represents the ultimate selectivity implemented by the
> > BANDWIDTH control in the DSP IF and the (wider) roofing filter gets
> > selected automatically based on the BW control. Hope this helps. 73,
> > Allan, W1AEL in Sevierville, TN.
> >
> > ----- Original Message -----
> > From: <K5XS@aol.com>
> > To: <tentec@contesting.com>
> > Sent: Saturday, January 20, 2007 8:14 AM
> > Subject: [TenTec] O-2 Screen Lines
> >
> >
> >
> >> > This is truly fun. I am figuring out the radio and trying to
discover
> >> > every
> >> > little nook and cranny on it.
> >> >
> >> > One thing has me puzzled, and I can't find it in the manual.
> >> >
> >> > Immediately above the spectrum sweep scope is a horizontal line on
> >> > which
> >> > the
> >> > rectangles representing the bandpasses for the main (left) and sub
> >> > (right)
> >> > receivers rest. The line has a break in it, and it is decidedly off
> >> > center
> >> > (to the lest a bit).
> >> >
> >> > Does that line represent something? Does the break represent
> >> > something?
> >> >
> >> > Thanks
> >> >
> >> > Bernie K5XS
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
________________________________________________________________________
Check out the new AOL. Most comprehensive set of free safety and security
tools, free access to millions of high-quality videos from across the web, free
AOL Mail and more.
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|