Good desoldering wick, no junk from Radio Shack.
David Goncalves
W1EUJ
On Thu, Apr 1, 2010 at 12:36 PM, <davkozy@comcast.net> wrote:
>
>
> Thanks all for your suggestions!! I did find a source for replacement
> relays www.onlinecomponents.com that had them in stock. ($1.77 ea. +
> Shipping) I'm waiting for them to arrive.
> Hope to find the time to install now with the nice weather setting in.
>
>
>
> Anyone have any tricks for easy desoldering?
>
>
>
> Dave KB9EPL
>
>
>
> ----- Original Message -----
> From: "phil g" <trapperpg@earthlink.net>
> To: geraldj@weather.net, "Discussion of Ten-Tec Equipment" <
> tentec@contesting.com>
> Sent: Monday, March 29, 2010 2:52:24 PM GMT -06:00 US/Canada Central
> Subject: Re: [TenTec] Pegasus 550
>
> I never noticed the pull-in voltage. I had that link bookmarked in my
> pegasus files as a replacement. I think it came from this list. I no
> longer have my 550, but maybe someone out there is adventurous and could do
> a voltage check.
>
> There is a 5v version listed, apparently also made of unobtainium.
>
>
> http://www.newark.com/panasonic-ew/als2b05tw/miniature-power-relay/dp/45M7085
>
> n4zsa
> ----- Original Message -----
> From: "Dr. Gerald N. Johnson" <geraldj@weather.net>
> To: <tentec@contesting.com>
> Sent: Monday, March 29, 2010 2:36 PM
> Subject: Re: [TenTec] Pegasus 550
>
>
> > The part number indicates a 12 volt coil.
> >
> > 73, Jerry, K0CQ
> >
> > On 3/29/2010 12:21 PM, Denton wrote:
> >> I used to have a Peggy, and one of the relays on the band pass filter
> >> board
> >> failed...if I remember right, the relay coils for both input and output
> >> of
> >> the filter are wired in series...I replaced mine with two new relays
> that
> >> had 6 volt coils.
> >> ----- Original Message -----
> >> From: "phil g"<trapperpg@earthlink.net>
> >> To: "Discussion of Ten-Tec Equipment"<tentec@contesting.com>
> >> Sent: Monday, March 29, 2010 11:04 AM
> >> Subject: Re: [TenTec] Pegasus 550
> >>
> >>
> >>> Here is a link to the relay. Also avail. from Ten Tec.
> >>> http://www.newark.com/jsp/search/productdetail.jsp?SKU=45M7086
> >>>
> >>> Fairly straight forward to replace. Unsolder the old, solder in the
> >>> new.
> >>>
> >>> n4zsa
> >>> ----- Original Message -----
> >>>
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
--
David Goncalves
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|