TenTec
[Top] [All Lists]

[TenTec] Dad's "shack cleaning" - values?

To: TenTec@contesting.com
Subject: [TenTec] Dad's "shack cleaning" - values?
From: Al Gulseth <wb5jnc@centurytel.net>
Reply-to: wb5jnc@centurytel.net, Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Fri, 14 May 2010 21:10:27 -0500
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Greetings all,

As some of you may remember I've been helping to "downsize" my 94 y.o. dad's 
ham gear due to his change in residence, so I have some of his Ten-Tec items 
(along with some of my own) that I'd like to find a home for.. The issue I'm 
encountering is that I'm not always sure what some of the "goodies" are 
worth. What might the values and/or interest level in the following items be? 
(I can send pics of individual items if that would help.)

1. Model 283 remote VFO for Delta - nice physical condition, but has been 
sitting for probably 10 years so the PTO needs fresh lube. My best guess 
(knowing dad and from what I remember on the VFO) he bought it, sent it to TT 
for a checkup, possibly hooked it up and used it for a short time before it 
went on a closet shelf when they made the spring or fall pilgrimage to the 
other QTH. I'm not sure it was used again after that. There should be a 
manual floating around here in another box somewhere. I'm unable to test it 
as I don't have a Delta.

2. Model KR-20A single lever keyer, black/silver, minor scratches. Haven't 
hooked it up to a rig to test actual keying, but it does work via the 
sidetone generator.

3. Model KR-20 dual lever paddle, eggshell/light olive(?)/woodgrain, minor 
scratches, right side panel has some holes drilled and a small speaker 
installed inside for the sidetone. Haven't hooked it up to a rig to test 
actual keying, but it does work via the sidetone generator.

4. Model 252G power supply, early production with 6 pin Jones connector, 
black/silver, minor scratches. I believe it works but haven't tested to make 
sure.

5. Model 227 antenna tuner, noticeable scratches (mostly on the top cover.)

6. Omni D/B, minor scratches and nicks. I haven't tested it fully, but the PTO 
is stiff (probably from sitting) and the hundreds (xxXxx.x) digit doesn't 
always come on (as per other posts on this reflector, pressing on the bezel 
generally brings it to life, so it's probably a connector or solder issue.) 
No optional filters installed. I did test it briefly at low power so I think 
the TX chain is probably OK.

7. If memory serves me correctly there is also a NIB mobile mount for a Delta 
580. (Just have to find the box it's in again....)

8. Not sure if it's Ten-Tec or not, but there's a looks to be new small black 
(anodized/brushed?) aluminum mounting plate  (~ 5.5 x 7) that has several 
sets of holes drilled in it. If this "rings a bell" for anyone as to what it 
belongs to, please let me know, because I haven't been able to positively 
identify it yet - and unfortunately, dad is to the point that he probably 
wouldn't be able to remember what he bought it for or what it went with....

Any ideas on the value of these items? I can provide pics, more info, and some 
operational tests if desired.

TNX/73, Al
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>
  • [TenTec] Dad's "shack cleaning" - values?, Al Gulseth <=