TenTec
[Top] [All Lists]

Re: [TenTec] Orion 2 Firmware 2.044A Released

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Orion 2 Firmware 2.044A Released
From: John Sheeley <wb4qda@yahoo.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Fri, 11 Jun 2010 12:00:46 -0700 (PDT)
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Ray
When I speak into the Micrphone  with the mode set to AM ,I  modulates up to 80 
watts .Tune is 21 watts and tune then the  PWR I get 95 watts  output.
73
John



----- Original Message ----
From: "Rsoifer@aol.com" <Rsoifer@aol.com>
To: tentec@contesting.com
Sent: Fri, June 11, 2010 10:38:22 AM
Subject: Re: [TenTec] Orion 2 Firmware 2.044A Released

John,

Funny thing about that.  With the mode set to AM, when I hit Tune and  then 
Pwr I get full output like you did, but if I hit the PTT button instead,  
all I get is 11 watts on the Bird.  It worked fine with 2.041XT.

73 Ray




In a message dated 6/11/2010 3:22:43 P.M. GMT Standard Time,  
wb4qda@yahoo.com writes:

Ray  
I just tested my O2 on AM  max output was 80 warrs on an Alpha watt  meter 
also about the same reading on a LP-100A watt meter with the Power set  to 
100%
using the new fearmware version 2.044A
73
John  wb4qda


----- Original Message ----
From: "Rsoifer@aol.com"  <Rsoifer@aol.com>
To: ronc@sonic.net; w5pny@arrl.net;  tentec@contesting.com
Sent: Fri, June 11, 2010 8:36:18 AM
Subject: Re:  [TenTec] Orion 2 Firmware 2.044A Released

Ron,

The NR problem  has been fixed (!) but the old low-output problem on AM is  

back.  Mine measures 11 watts carrier power, max.  It  worked  fine with 
2.041XT.

73 Ray W2RS


In a message  dated 6/11/2010 2:17:05 A.M. GMT Standard Time, 
ronc@sonic.net  
writes:

I have  adjusted the "Wish List" for the Orion II to  reflect the newest 
version of  the firmware.  It's at  www.N6IE.com

Ron  N6IE
www.N6IE.com

----- Original  Message ----- 
From: "Harry G McGavran  Jr"  <w5pny@arrl.net>
To: <tentec@contesting.com>
Sent:  Thursday, June 10, 2010 5:50 PM
Subject: Re: [TenTec] Orion 2  Firmware  2.044A Released


>
> With this one I can set  the side-tone  level all the way
> up to 65 before the pops begin,  and by the time  one
> gets past 80 on towards 99 the distortion on  the
> side-tone  is still really bad -- BUT -- for me at
>  least, levels are 50-60 are  all I need and that is
> now  distortion free, at least with a 610 Hz  sidetone
> which is the  only one I tested or use.  I also  am
> using the speaker and  not headphones for this.
> Since one  gets the side-tone every time  the SPOT
> button is used, the side-tone  distortion was  really
> objectionable with 2.043B.
>
> The  NR seems  better too, but most all the time I don't
> really need it --  and  it's nice not to have artifacts that
> sound like NR action on the  side-tone which the side-tone
> is set to 50-60.
>
>  There  are a few CAT wierdnesses here and there, but the  reliability
> of  sending a strings of "*" commands seems  better.
>
> Unless  something else crops up, I think I can  live with this
>  release...
>
> 73 --
>
>  Harry,  W5PNY
>
>
>
>
>
> --  
>
>  Harry G. McGavran, Jr.
>
> E-mail:  w5pny@arrl.net
>
>
>
>  _______________________________________________
> TenTec mailing  list
> TenTec@contesting.com
>  http://lists.contesting.com/mailman/listinfo/tentec
>  

_______________________________________________
TenTec  mailing  list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec  mailing  list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec




_______________________________________________
TenTec  mailing  list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec



      
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>