OMNI-VII Receive and Transmit Modes for use with DXLab Commander
The following commands were derived from page 18 of OMNI-VII, Model 588,
Programmer's Reference Guide, Revision 1.009 which is available at
<http://www.tentec.com/?id=2> and from
<http://www.dxlabsuite.com/commander/Help/CommandSequences.htm>.
Button ( command ) what it does
F-5 [ USB ] ( '*M13<13> ) sets VFOA to USB, VFOB to CWU
F-6 [ LSB ] ( '*M25<13> ) sets VFOA to LSB, VFOB to CWL
F-7 [ CW ] ( '*M31<13> ) sets VFOA to CWU, VFOB to USB
F-8 [ AM ] ( '*M02<13> ) sets VFOA to AM, VFOB to LSB
Note: by using the front panel A/B button, set the VFO with the TRANSMIT
mode desired to the DX pile frequency and adjust the bandwidth as desired.
In the same manner set opposite VFO to the DX ( your receive) and adjust the
bandwidth as desired. On the Commander panel split VFOs by checking the
"Split" box, mouse over, click on and hold the XFC button to monitor the
pile or manually tune the VFO via the OMNI-VII (BIG knob), release to
transmit from a frequency in the pile (DX's receive frequency).
F-9 [ U-U ] ( '*M11<13> ) sets both VFOs to USB
F-10 [ L-L ] ( '*M22<13> ) sets both VFOs to LSB
F-11 [ UC-UC ] ( '*M33<13>) sets both VFOs to CWU
F-12 [ AM-AM] ( '*M00<13>) sets both VFOs to CWU
Questions - email glhuber@msn.com
73,
Gary - AB9M
--------------------------------------------------
From: "CSM(r) Gary Huber" <glhuber@msn.com>
Sent: Saturday, August 07, 2010 6:16 PM
To: <dxlab@yahoogroups.com>
Cc: "TenTec Reflector" <tentec@contesting.com>;
<Ten-Tec-Omni-VII@yahoogroups.com>
Subject: Re: [TenTec] [dxlab] HRD & DXLab
On a related note, I will submit the Commander command sequences for
OMNI-VII TX/RX VFO mode splits later this evening.
By using a different mode in each VFO, different bandwidths may be used
for the DX and the pile.
73,
Gary - AB9M
From: Dave AA6YQ
Sent: Saturday, August 07, 2010 12:01 PM
To: dxlab@yahoogroups.com
Subject: RE: [dxlab] HRD & DXLab
AA6YQ comments below
-----Original Message-----
From: dxlab@yahoogroups.com [mailto:dxlab@yahoogroups.com]On Behalf Of
Jerry Keller (K3BZ)
Sent: Saturday, August 07, 2010 12:57 PM
To: (REFLECTOR) DXLAB
Subject: [dxlab] HRD & DXLab
I keep hearing about HRD and thought I'd try it with DXLab, just for fun.
Couple questions:
Has the new HRD matured enough now for use with DXLab? (with HRD Bridge)
As far as I know, HRD still can't be directed to set VFO B or
enable/disable split, so if you double-click a Spot Database Entry for a
station operating split, you'll have to manually setup your transceiver
for
split frequency operation.
If I install HRD Bridge and HRD, and don't like it, is it easy to reverse
the process and get back where I was?
Yes -- you'd simply terminate HRD and the HRD bridge, and run Commander
instead.
73,
Dave, AA6YQ
__._,_.___
Reply to sender | Reply to group | Reply via web post | Start a New Topic
Messages in this topic (2)
Recent Activity: a.. New Members 6 a.. New Files 2
Visit Your Group
MARKETPLACE
Stay on top of your group activity without leaving the page you're on -
Get the Yahoo! Toolbar now.
--------------------------------------------------------------------------------
Get great advice about dogs and cats. Visit the Dog & Cat Answers Center.
--------------------------------------------------------------------------------
Hobbies & Activities Zone: Find others who share your passions! Explore
new interests.
Switch to: Text-Only, Daily Digest . Unsubscribe . Terms of Use.
__,_._,___
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|