Re: [TenTec] Corsair II U10 Problems

[Bwana Bob <wb2vuf@verizon.net>]

How about one of the AADE (Almost All Digital Electronics) display kits?

http://aade.com/dfd2.htm

                        73,

                        Bob WB2VUF


On 5/28/2011 6:37 PM, Barry N1EU wrote:
> Jerry, manual is available at http://tentec.com/files/Corsair%20Manual.pdf
>
> Understood about wanting to stick with the PTO for the cleanest
> possible signal.  If you find a replacement for the display, please
> post the info to the list.
>
> One thing that appeals to me about the PTO option is getting a
> smoother, weightier tuning action with variable tuning rate.  I wish I
> could install my hefty Omni 6 tuning knob on my Corsair, but the shaft
> diameters are different.
>
> 73/GL, Barry N1EU
>
>
>
> On Sat, May 28, 2011 at 10:17 PM, Jerry Haigwood<jerry@w5jh.net>  wrote:
> > Barry,
> >      The reason I purchased the Corsair was to get rid of a DDS.  I would not 
> > want to ruin a perfectly good receiver by adding more digital noise/spurs to 
> > it.  I have other rigs which have a DDS in them if I want to listen to the 
> > noise.  :-) I am currently looking at a replacement for the Corsair II display. 
> >  It may also fit the Corsair I.  However, I don't have enough info on how the 
> > Corsair I works.  Anyone have a manual I could look at?
> > Jerry W5JH
> >
> > -----Original Message-----
> > From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com] On 
> > Behalf Of Barry N1EU
> > Sent: Saturday, May 28, 2011 1:11 PM
> > To: Discussion of Ten-Tec Equipment
> > Subject: Re: [TenTec] Corsair II U10 Problems
> >
> > No, I wouldn't assume your 68705 is going to fail anytime soon.  If it
> > did, you could either:
> >
> > 1. purchase a parts rig to have spare boards on hand OR
> > 2. replace the PTO with DDS VFO which could drive a freq. display directly
> >
> > 73/GL,
> > Barry N1EU
> >
> > On Sat, May 28, 2011 at 5:43 PM, Jerry Haigwood<jerry@w5jh.net>  wrote:
> > > All,
> > >
> > >      I am new to the list and also new to the Corsair II I recently
> > > purchased.  I have seen some U10 problems recently.  If U10 truly fails,
> > > what are the options for repair?  I have been told Ten Tec no longer has any
> > > U10 (68705) ICs.  Anybody know if that is true?  I recently purchased a 288
> > > filter and 263G VFO from a ham who had U10 fail.  He decided to part out the
> > > radio rather than repair it.  I also see a corsair on QTH.Com which has U10
> > > problems.  Is the U10 problem something I should "look forward to?"
> > >
> > > Jerry W5JH
> > >
> > >
> > >
> > > _______________________________________________
> > > TenTec mailing list
> > > TenTec@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/tentec
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
> -----
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 10.0.1375 / Virus Database: 1509/3669 - Release Date: 05/30/11