TenTec
[Top] [All Lists]

Re: [TenTec] Need push on/off pots for Omni C

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Need push on/off pots for Omni C
From: Clayton Brantley <clayton_n4ev@yahoo.com>
Reply-to: Clayton Brantley <clayton_n4ev@yahoo.com>, Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Thu, 13 Jun 2013 13:55:41 -0700 (PDT)
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Randy, would a S meter from an Omni VI work?   I do have a spare one around.

Clayton N4EV




________________________________
 From: GARY HUBER <glhuber@msn.com>
To: Discussion of Ten-Tec Equipment <tentec@contesting.com> 
Sent: Thursday, June 13, 2013 1:04 PM
Subject: Re: [TenTec] Need push on/off pots for Omni C
 

It seems to me that the old OMNI series radios can be repaired if you can find 
a substitute part which can be made to work. The are no proprietary chips or 
devices. Its pretty much WYSIWYG an analog PTO radio, just read the schematic, 
look at the parts, find a replacement part which works,  repair the old part, 
or make a substitute.


73 ES DX,
Gary -- AB9M

-----Original Message----- From: Randy Fulco
Sent: Wednesday, June 12, 2013 11:29 PM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] Need push on/off pots for Omni C

I spent 3 hours on it, pulled front panel and then unsolder/pulled the pots. I 
actually was able to pull them apart, and push the shaft in and out to get it 
unstuck and then put some grease in and put them all back together and make it 
work as new. Once you get the pot out not as hard as I thought. Only problem, 
the S meter has some corrosion, and the fine wire is broke inside! I was on my 
way to getting this trash can Omni back to life...Got the speaker ps going last 
night..Now to just find a old S meter! Thank for reply..Randy

--- On Wed, 6/12/13, Richard Detweiler <rdetweil@hotmail.com> wrote:


From: Richard Detweiler <rdetweil@hotmail.com>
Subject: Re: [TenTec] Need push on/off pots for Omni C
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Date: Wednesday, June 12, 2013, 11:35 AM


Randy,



Those are very hard to find,  some people ran 12V through the power switch and 
burned them as there weren't designe for that current.

There were only meant to power the AC line to the power supply.



Best find any push/pull pot of any value then replace the resistor plate with 
one that works or the original if not damaged.



I have a surplus store here that sells the 100 ohm version in the same body 
style,



What I have done in the past is open the front of the 100 ohm one by lifting 
the tabs and then replaced the carbon resistor plate with the correct value.



If you can't use the original plate,  Make sure you find the right type of 
resistor plate,  there is a  audio taper and a linear taper.



Hope that help.

Best Wishes
Richard
K5SF



> Date: Tue, 11 Jun 2013 23:22:53 -0700
> From: rfulco@bellsouth.net
> To: tentec@contesting.com
> Subject: [TenTec] Need push on/off pots for Omni C
> 
> I picked up a neglected Omni C with matching supply/speaker this weekend at 
> Hamfest. Lots of oxidation/ rust on bolts on inside. I free'd up most pots, 
> but  the push on/off with pots --don't move in or out. Anyone got any spare's 
> they want to part with? Randy K5SL
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec 
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>