TenTec
[Top] [All Lists]

Re: [TenTec] Corsair II noise blanker

To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Subject: Re: [TenTec] Corsair II noise blanker
From: "A R" <raf_3@msn.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Thu, 27 Mar 2014 09:43:27 -0700
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Yes, the circuitry is different. The 81401 IC complement is 2-MC1350P's and 
1-LM358N, and it has 6 transistors and 3 diodes. Interface to the NB level and 
NB width pots (connectors #7 and 22 respectively) are both 2-pin connectors.

. 
  ----- Original Message ----- 
  From: Doug Reid<mailto:n1068d@aol.com> 
  To: tentec@contesting.com<mailto:tentec@contesting.com> 
  Sent: Thursday, March 27, 2014 6:01 AM
  Subject: Re: [TenTec] Corsair II noise blanker


  Have you confirmed that the newer board is a completely different design from 
your old board ? Are the components different ?  I have an Argonaut 505 and the 
power amp board is a different number from what is shown in the 505 manual. It 
is identical to the newer boards built for the 509. But the number on the board 
is not the same.  Back in the day, I have a feeling new boards were tried and 
superseded without much documentation.

  Doug WD4LNW

  Sent from AOL Mobile Mail


  -----Original Message-----
  From: A R <raf_3@msn.com<mailto:raf_3@msn.com>>
  To: tentec <TenTec@contesting.com<mailto:TenTec@contesting.com>>
  Sent: Wed, Mar 26, 2014 10:04 PM
  Subject: [TenTec] Corsair II noise blanker



  <div id="AOLMsgPart_1_0b3d700d-3241-4930-aedb-e5f57f74355a" style="margin: 
0px;font-family: Tahoma, Verdana, Arial, Sans-Serif;font-size: 12px;color: 
#000;background-color: #fff;">

  <pre style="font-size: 9pt;"><tt>Of my two Corsair II's, one has a NB board 
p/n 80977, which correspond to the NB called out in the manual. The other 
Corsair II has a NB board p/n 81401, for which I've not been able to find any 
documentation. TenTec has been unable to find documentation for this NB, 
despite the fact that it appears to be of production quality (not one-off lab 
bench quality). Does anyone else have a Corsair II with the 81401 NB, or any 
information (schem and interface interconnect) for this NB? The 81401 NB has 
roughly 2/3 the component count of the 80977, and has no unpopulated holes or 
device hole patterns. S/N of the Corsair II with the "rogue" NB is 561-02258.

  Thanks,
  Allen---W7GIF 
  _______________________________________________
  TenTec mailing list
  <a 
href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a<mailto:TenTec@contesting.com%22%3ETenTec@contesting.com%3C/a>>
  <a 
href="http://lists.contesting.com/mailman/listinfo/tentec<http://lists.contesting.com/mailman/listinfo/tentec>"
 target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>
  </tt></pre>
   <!-- end of AOLMsgPart_1_0b3d700d-3241-4930-aedb-e5f57f74355a -->
  </div>
  _______________________________________________
  TenTec mailing list
  TenTec@contesting.com<mailto:TenTec@contesting.com>
  
http://lists.contesting.com/mailman/listinfo/tentec<http://lists.contesting.com/mailman/listinfo/tentec>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>