The problem is with radios that have a DSP-AGC.
The Omni VI+ and Corsair-II do not have DSP-based AGC.
The problem is with almost every transceiver currently on the market, except
those I listed previously (Flex, Elecraft, and recently the Ten-Tecs). It
was not a problem in radios 10 years ago or earlier.
Rob demonstrated this in many of his past presentations, using audio files
to show how bad it was.
In fact he used the OM7 as a typical example of how bad it can be.
If you want to see and hear a specific example of this, one of the best
places to go is Rob's 2009 BARC (Boulder Amateur Radio Club) presentation.
Go to slides nr. 62 ("AGC Impulse Noise Anomaly"), then view the next 3
slides as well.
On slide 63 (bottom screen shot) you clearly see the pulse that is causing
the disturbance to the AGC. The two audio clips are in files entitled
"ImpulseRight30Sec.wav" and "ImpulseLeft30Sec.wav". This was a simultaneous
recording of two radios at the same time on the same frequency, with a 756
Pro III recorded as "Right" and the OM7 recorded as "Left".
This presentation is on my web site, along with the HUGE audio file.
I have also extracted the two audio clips and show them as separate
downloads at the bottom of the page.
http://www.dj0ip.de/transceivers/sherwood-presentations/barc-2009/?logout=1
73 - Rick, DJ0IP
(Nr. Frankfurt am Main)
-----Original Message-----
From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Bill Cotter
Sent: Friday, March 28, 2014 4:35 PM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] Corsair II noise blanker
The NB in my OMNI-VI+ and Corsair-II work great to eliminate electric fence
noise and lightning bursts.
73 Bill N4LG
At 10:07 PM 3/27/2014, you wrote:
>Do any of these TT noise blankers do anything for you guys. Mine
>appears to do very little in my Omni VI Plus...
>
>Best regards - Bry Carling
>
>
>
> > On Mar 26, 2014, at 10:03 PM, "A R" <raf_3@msn.com> wrote:
> >
> > Of my two Corsair II's, one has a NB board p/n 80977, which
> correspond to the NB called out in the manual. The other Corsair II
> has a NB board p/n 81401, for which I've not been able to find any
> documentation. TenTec has been unable to find documentation for this
> NB, despite the fact that it appears to be of production quality (not
> one-off lab bench quality). Does anyone else have a Corsair II with
> the 81401 NB, or any information (schem and interface interconnect)
> for this NB? The 81401 NB has roughly 2/3 the component count of the
> 80977, and has no unpopulated holes or device hole patterns. S/N of
> the Corsair II with the "rogue" NB is 561-02258.
> >
> > Thanks,
> > Allen---W7GIF
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
>_______________________________________________
>TenTec mailing list
>TenTec@contesting.com
>http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|