TenTec
[Top] [All Lists]

Re: [TenTec] Orion ll

To: "TenTec@contesting.com" <tentec@contesting.com>
Subject: Re: [TenTec] Orion ll
From: P C A <xtraham58@hotmail.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Mon, 6 Oct 2014 15:54:24 -0400
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
OK, Bob I only looked at the side, tnx
Andy

> 
> The 4 large Phillips screws are standard on the sides.  The Torx are at the 
> rear of the case.  Normally a Torx wrench is supplied with the accessory kit 
> from Tentec.
> 
> 73
> Bob, K4TAX
> 
> 
> 
> DISCLOSURE:
> All opinions expressed herein are solely those of K4TAX and do not reflect 
> opinions, ideas, policy or practice of other persons or companies including 
> R F Concepts.
> 
> This is to inform all persons I am a Ten-Tec Ambassador and I receive 
> compensation according to the Ten-Tec Ambassador program.  In addition, I 
> serve as a volunteer beta test person to Ten-Tec for the Omni VII, Eagle and 
> Argonaut VI radios.  I am not an employee of Ten-Tec and hold no employment 
> relationship, no financial or other interests, nor do I conduct any 
> commercial business, direct or indirect, with Ten-Tec.
> 
> 
> 
> 
> 
> ----- Original Message ----- 
> From: "P C A" <xtraham58@hotmail.com>
> To: "TenTec@contesting.com" <tentec@contesting.com>
> Sent: Monday, October 06, 2014 12:42 PM
> Subject: Re: [TenTec] Orion ll
> 
> 
> > Barry tnx for the reply. Yes, I have a #10 Torx but to my surprise the 4 
> > screws, 2 each side, are a #2 phillips head. Large rather flat head. I 
> > wonder why the difference.Tnx Andy, W3LI
> >
> >> Date: Mon, 6 Oct 2014 17:31:46 +0000
> >> From: barry.n1eu@gmail.com
> >> To: tentec@contesting.com
> >> Subject: Re: [TenTec] Orion ll
> >>
> >> http://www.tentecwiki.org/doku.php?id=565battery
> >>
> >> You'll need a Torx T10 tool to remove the cover.
> >>
> >> Barry N1EU
> >>
> >> On Mon, Oct 6, 2014 at 5:24 PM, P C A <xtraham58@hotmail.com> wrote:
> >>
> >> > After talking with the folks at TT service, I think that it is time to
> >> > install a new battery. This radio has been in service since Feb 2006.
> >> > Have any of you folks performed this task? Up till now I have not 
> >> > removed
> >> > the covers for any reason. Looking for any suggestions or adviceon 
> >> > doing
> >> > this.
> >> > Thank you for any help.
> >> > Andy, W3LI
> >> > _______________________________________________
> >> > TenTec mailing list
> >> > TenTec@contesting.com
> >> > http://lists.contesting.com/mailman/listinfo/tentec
> >> >
> >> _______________________________________________
> >> TenTec mailing list
> >> TenTec@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/tentec
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> > 
> 
> 
> 
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
                                          
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>