TenTec
[Top] [All Lists]

Re: [TenTec] Orion 565 XMIT alignment

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Orion 565 XMIT alignment
From: Mike Schatzberg <cherokeehillfarm@earthlink.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Sat, 5 Nov 2016 16:49:02 -0400
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Yes, you can calibrate the display in watts, average or just key down. I used 
100 watts and calibrated there.

73,

Mike
W2AJI  

Sent from my iPhone

> On Nov 5, 2016, at 3:02 PM, art N4UC <n4uc@hotmail.com> wrote:
> 
> Thanks a lot Mike, that answers the ALC aspect of the question. Just for 
> clarification though, you say to set the ALC SET to where the actual RF 
> output as measured by an external wattmeter is about 110% of the pwr setting 
> on the front panel. In this case you're looking for 110W on the external 
> meter, correct?  Is the number on the front panel (100 in this case) supposed 
> to represent power output in watts or percentage of maximum output? Is this 
> possibly where the PWR pot comes into play, to adjust power output reading on 
> the analog meter?
> 
> 
> ________________________________
> From: TenTec <tentec-bounces@contesting.com> on behalf of Mike Schatzberg 
> <cherokeehillfarm@earthlink.net>
> Sent: Saturday, November 5, 2016 7:11 AM
> To: Discussion of Ten-Tec Equipment
> Subject: Re: [TenTec] Orion 565 XMIT alignment
> 
> Take a look on my page.  It was written for the 566 and may help.
> 
> 
> http://home.earthlink.net/~cherokeehillfarm/id2.html
> [http://home.earthlink.net/~cherokeehillfarm/sitebuildercontent/sitebuilderpictures/mvc-018f.jpg]<http://home.earthlink.net/~cherokeehillfarm/id2.html>
> 
> AMATEUR RADIO STATION W2AJI - 
> EarthLink<http://home.earthlink.net/~cherokeehillfarm/id2.html>
> home.earthlink.net
> Welcome to W2AJI, Tryon, North Carolina. First licensed in 1961, this year 
> marks 50 years of continuous operation of W2AJI. Mike has been associated 
> with the wire ...
> 
> 
> 
> 73,
> 
> Mike
> W2AJI
> 
> Sent from my iPhone
> 
>> On Nov 5, 2016, at 1:46 AM, art N4UC <n4uc@hotmail.com> wrote:
>> 
>> Does anyone have the procedure to set the PWR, ALC, REF, etc... pots on the 
>> A5 board?
>> 
>> Thanks in advance, 73
>> 
>> Art N4UC
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
> TenTec Info Page - 
> Contesting<http://lists.contesting.com/mailman/listinfo/tentec>
> lists.contesting.com
> Welcome to the Ten-Tec mailing list! This list is intended for the exchange 
> of information on Ten-Tec-related topics ONLY. Off Topic subject postings 
> should be ...
> 
> 
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> TenTec Info Page - 
> Contesting<http://lists.contesting.com/mailman/listinfo/tentec>
> lists.contesting.com
> Welcome to the Ten-Tec mailing list! This list is intended for the exchange 
> of information on Ten-Tec-related topics ONLY. Off Topic subject postings 
> should be ...
> 
> 
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>