Thank you so much for the update Ripley.
Sounds like you’ve done an extraordinary amount of troubleshooting.
Kudos to you.
Are you able to use the rig in Pegasus Emulation Mode?
Something of the likes N4PY rig control?
Fernando N2FQ/6
n2fq@sbcglobal.net
> On Nov 8, 2017, at 8:09 PM, Bob Ripley <bob_ripley@hotmail.com> wrote:
>
> Hello Fernando,
>
>
>
> This radio that was donated to us is said to have taken a lighting strike and
> had/has multiple problems. The persons that worked on it before me fixed the
> power supply protection circuit but when you turned it the transceiver was
> receiving and transmitting at the same time. Not good. They tried a couple of
> things but gave up.
>
>
>
> Since joining the staff at the Museum I was asked to look at this radio.
> After a few hours of bench time I isolated the “always transmitting” issue
> down to the ADS micro-controller on the LOGIC/DSP card and replaced that 128
> pin surface mount beauty with its replacement that arrived in the mail today.
> The new chip fixed that problem but not the VFO issue. Channel B on the
> encoder is fine but channel A is at Vcc level.
>
>
>
> I was finally able to see the marking hidden by the ribbon cable and the
> encoder that I need is a HRPG-ASAC#17F made by Avago. This particular encoder
> is a non stock item from about everyone (minimum order 150 units and a 14
> week delivery). I did find a similar encoder from the same manufacturer at
> Newark Electronics in the UK. This encoder has a cable instead of pins for a
> front mount circuit board application but I believe that I can adapt it for
> my needs. The encoder is about $40.00 and I should receive it in about a week
> to ten days.
>
>
>
> Right now the radio works except for the VFO. 100 watts out on CW, auto
> antenna tuner works, all of the front panel buttons seam to operate correctly
> and all of the other encoders work fine. This evening I found and fixed a
> problem with the PTT line. Turned out to be an open diode on the LOGIC/DSP
> board but then discovered that the ratty Ten Tec hand mic that they gave me
> to test this radio is bad or has a broken wire to the microphone element
> itself. I will check that out tomorrow.
>
>
>
> Ripley
>
> KD8UYQ
>
>
>
> Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986> for Windows 10
>
>
>
> ________________________________
> From: TenTec <tentec-bounces@contesting.com> on behalf of Fernando
> <n2fq@sbcglobal.net>
> Sent: Wednesday, November 8, 2017 10:15:14 PM
> To: Discussion of Ten-Tec Equipment
> Subject: Re: [TenTec] Replacement VFO encoder for TT Jupiter
>
> Sad news.
>
> One way to find a replacement is to get any info from the one
>
> in the radio.
>
> A search on the parts list yielded this: encoder hrpg
>
> A google search shows than Mouser has one for $32.
>
> A prudent thing to do is to ascertain that is what is written
>
> on the old one before ordering. Less than that I think the
>
> only thing else to do is remove the old one and try to match
>
> its characteristics with what is available.
>
> A long shot would be to contact Ten Tec.
>
> A have two Jupiters here and very interested in how you
>
> fair out. Let us know.
>
> 73
>
> Fernando N2FQ/6
> n2fq@sbcglobal.net
>
>
>
>
>> On Nov 8, 2017, at 12:56 PM, Bob Ripley <bob_ripley@hotmail.com> wrote:
>>
>> Hello there.
>>
>> It looks the VFO encoder on our Jupiter has gone south. Spin the knob all
>> that you want and nothing happens the same is true when the MENU screen is
>> pulled up. Anyone know where I can get a replacement Encoder for this
>> transceiver.
>>
>> Thank you in advance for your response.
>>
>> Bob Ripley
>> KD8UYQ
>> Museum of Radio and Technology
>> Huntington, WV
>>
>> Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986> for Windows 10
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|