TenTec
[Top] [All Lists]

Re: [TenTec] Omni VI Plus w/ TL-922A

To: tentec@contesting.com
Subject: Re: [TenTec] Omni VI Plus w/ TL-922A
From: Joe Papworth via TenTec <tentec@contesting.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Sat, 17 Mar 2018 19:49:20 -0400
List-post: <mailto:tentec@contesting.com>
Yikes Rick, that sounds ominous.

<div>My XCVR is an Omni VI Plus, not an Eagle, but I'm guessing the same 
situation would exist.

However, I've been keying an L4B and an SB-200 with it for 20 years without a 
problem. I know the SB-200 has an open frame relay. I'm not sure about the 
Drake.

Any additional thoughts?

Thanks, Joe, K8MP

Sent from AOL Mobile Mail


-----Original Message-----
From: Rick <Rick@dj0ip.de>
To: 'Discussion of Ten-Tec Equipment' <tentec@contesting.com>
Sent: Sat, Mar 17, 2018 05:57 PM
Subject: Re: [TenTec] Omni VI Plus w/ TL-922A


Houston, we have a PROBLEM.

The 922 has an open-frame TR-relay that is very slow.
The Eagle sends RF to the amp, long before it is ready to see RF.
This will result in burning of relay contacts; takes a while, a year or two,
but then it suddenly dies.

You MUST delay RF to the relay by about 25 mS.
In theory the Eagle delays the RF by 17 mS.
In reality it's currently only 10mS or even less.
BURN BABY BURN.

The mod Bob just described, restores the delay to 17 mS, but you're still
shy about 8 mS.

The simple solution is to use an external keyer which has adjustable timing
delays.
The WINKEY is one such solution, the keyer I use, the MFJ-495 is another
solution.
My keyer has adjustable delay times!

Do not take this warning lightly!

73,
Rick, DJ0IP
(Nr. Frankfurt, Germany)

-----Original Message-----
From: TenTec <tentec-<a 
href="mailto:bounces@contesting.com";>bounces@contesting.com</a>> On Behalf Of 
Joe Papworth via
TenTec
Sent: 17 March 2018 22:42
To: <a href="mailto:tentec@contesting.com";>tentec@contesting.com</a>
Cc: <a href="mailto:k8mp@aol.com";>k8mp@aol.com</a>
Subject: Re: [TenTec] Omni VI Plus w/ TL-922A

Hi Rick,
99% cw. 
Thanks, Joe, K8MP

Sent from AOL Mobile Mail


-----Original Message-----
From: Rick <<a href="mailto:Rick@dj0ip.de";>Rick@dj0ip.de</a>>
To: 'Discussion of Ten-Tec Equipment' <<a 
href="mailto:tentec@contesting.com";>tentec@contesting.com</a>>
Sent: Sat, Mar 17, 2018 05:33 PM
Subject: Re: [TenTec] Omni VI Plus w/ TL-922A


You need to tell us if you plan to run CW or SSB.
That makes a big difference.

73,
Rick, DJ0IP
(Nr. Frankfurt, Germany)

-----Original Message-----
From: TenTec <tentec-<a
href="<a 
href="mailto:bounces@contesting.com";>bounces@contesting.com</a?">mailto:bounces@contesting.com";>bounces@contesting.com</a</a>>>
 On Behalf
Of Joe Papworth via TenTec
Sent: 17 March 2018 19:38
To: <a href="<a 
href="mailto:tentec@contesting.com";>tentec@contesting.com</a?">mailto:tentec@contesting.com";>tentec@contesting.com</a</a>>
Cc: <a href="<a 
href="mailto:k8mp@aol.com";>k8mp@aol.com</a?">mailto:k8mp@aol.com";>k8mp@aol.com</a</a>>
Subject: [TenTec] Omni VI Plus w/ TL-922A

Gents,
Has any one run an Omni VI Plus with a TL-922A? I'm planning on acquiring a
922A and am wondering if there are any things I should be aware of in
advance.

Thanks,
Joe, K8MP

Sent from AOL Mobile Mail
_______________________________________________
TenTec mailing list
<a href="<a 
href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a?">mailto:TenTec@contesting.com";>TenTec@contesting.com</a</a>>
<a href="<a href="http://lists.contesting.com/mailman/listinfo/tentec"; 
target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>"
target="_blank"><a 
href="http://lists.contesting.com/mailman/listinfo/tentec</a" 
target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a</a>>

_______________________________________________
TenTec mailing list
<a href="<a 
href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a?">mailto:TenTec@contesting.com";>TenTec@contesting.com</a</a>>
<a href="<a href="http://lists.contesting.com/mailman/listinfo/tentec"; 
target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>"
target="_blank"><a 
href="http://lists.contesting.com/mailman/listinfo/tentec</a" 
target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a</a>>
_______________________________________________
TenTec mailing list
<a href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a>
<a href="http://lists.contesting.com/mailman/listinfo/tentec"; 
target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>

_______________________________________________
TenTec mailing list
<a href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a>
<a href="http://lists.contesting.com/mailman/listinfo/tentec"; 
target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>
</div>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>