TenTec
[Top] [All Lists]

Re: [TenTec] Omni VI

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Omni VI
From: Byron Cordes via TenTec <tentec@contesting.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Mon, 01 Oct 2018 07:38:15 -0500
List-post: <mailto:tentec@contesting.com>
Ok I’ll do that tonight. Thanks for the help I really appreciate it. Byron

Sent from my iPad

> On Sep 30, 2018, at 10:01 PM, MadScientist <dukeshifi@comcast.net> wrote:
> 
> Pull cable marked “17” from the RF front end board and do the same test.
> 
> Gary
> 
>> On Sep 30, 2018, at 7:33 PM, Byron Cordes via TenTec <tentec@contesting.com> 
>> wrote:
>> 
>> Ok I pulled 9mhz filter and no more noise when vfo turned. Put 9mhz back in 
>> and pulled 6.3 and noise stopped. So noise coming out of mixer? 
>> 
>> Sent from my iPad
>> 
>>> On Sep 29, 2018, at 3:48 PM, Byron Cordes via TenTec 
>>> <tentec@contesting.com> wrote:
>>> 
>>> Yes rx is ok and tx is ok . You can’t hear anyone from the clicking noise 
>>> till you stop turning the vfo and when you stop it rx fine. 
>>> 
>>> Sent from my iPad
>>> 
>>>> On Sep 29, 2018, at 3:45 PM, MadScientist <dukeshifi@comcast.net> wrote:
>>>> 
>>>> OK, but, when this is happening, the radio still works fine (good TX and 
>>>> RX), right?
>>>> 
>>>> Gary
>>>> 
>>>>> On Sep 29, 2018, at 3:44 PM, Byron Cordes via TenTec 
>>>>> <tentec@contesting.com> wrote:
>>>>> 
>>>>> Radio has a click sound with each number on frequency readout when vfo 
>>>>> knob turned. This is on 20meters and higher. 40 -160 works normally. 
>>>>> Will look at radio again tomorrow night. 
>>>>> 
>>>>> Sent from my iPad
>>>>> 
>>>>>> On Sep 29, 2018, at 2:04 PM, MadScientist <dukeshifi@comcast.net> wrote:
>>>>>> 
>>>>>> Please explain this issue a bit more.
>>>>>> 
>>>>>> I am not clear of the meaning of the description "clicks for each number 
>>>>>> “.
>>>>>> 
>>>>>> Do you mean you hear a click in the speaker or what?
>>>>>> 
>>>>>> Dose the radio otherwise work on the higher bands?
>>>>>> 
>>>>>> Gary
>>>>>> 
>>>>>>> On Sep 25, 2018, at 8:51 PM, Byron Cordes via TenTec 
>>>>>>> <tentec@contesting.com> wrote:
>>>>>>> 
>>>>>>> Hi everyone 
>>>>>>> I have a Omni VI that I’m down to one last problem.
>>>>>>> On 20 meters or higher  when you turn the VFO the radio clicks for each 
>>>>>>> number . Anyone have any idea? 
>>>>>>> Thanks Byron AC9PA 
>>>>>>> 
>>>>>>> Sent from my iPad
>>>>>>> _______________________________________________
>>>>>>> TenTec mailing list
>>>>>>> TenTec@contesting.com
>>>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>>> 
>>>>>> _______________________________________________
>>>>>> TenTec mailing list
>>>>>> TenTec@contesting.com
>>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>> _______________________________________________
>>>>> TenTec mailing list
>>>>> TenTec@contesting.com
>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>> 
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
> 
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
<Prev in Thread] Current Thread [Next in Thread>