Corsair, Remote VFO, Crystal, Omni 546 and
Century 21 parts, and more For Sale:
.
TenTec 560 Corsair, HF transceiver:
Many consider the Corsair to be the best rig
that TenTec ever made, before the Orion or
Eagle. It is not a synthesized rig, so phase
noise is virtually nonexistent. This means that
it has a really superb receiver that is far
better than most of the Japanese rigs.
It covers 160 thru 10 meters, including the
WARC bands, and has such things such as band
pass tuning, notch filter, QSK, noise blanker, etc.
A speech processor is also included.
It has up to 100 watts output, with front
panel adjustment for QRP, and is all solid
state.
This one has the optional 8 pole filter in
the 9 MHz IF, for additional selectivity.
Electrically, everything works 100%. The PTO
is smooth and works great. Cosmetically,
it is also in great condition. No defects that
I can find. Manual is included for $400.
.
TenTec 263 Remote VFO
The 263 remote VFO goes with the Corsair to
provide the rig with much more frequency
agility.
With the 263 remote VFO, one can transceive
on the rig's VFO, as normal, transceive on
the remote VFO, receive on the rig's VFO
and transmit on the remote (split), or the
reverse. In addition it permits one to receive
on BOTH frequencies, and transmit on either
one. Very versatile.
This one works like it should. It looks
really great.
Paper work is included for $175.
.
Crystal for 12 m for Omni 546 series A or B
The early Omni series (A and B) did not include
the WARC bands, but they do have an "Aux"
position that can be used for the 12 meter
(24.8 MHz) WARC band, by simply plugging in
a crystal.
This is the crystal you need to do this.
It works fine. Only $18.
.
TenTec Omni 546 Parts For Sale:
I have a TenTec Omni D, Series B, Model 546 that I
am parting out.
Many, probably most, of the parts are compatible
with most all of the Omni series A, B, and C rigs.
PTO, digital readout and final module are
gone, but many, many parts are still available.
Available:
Metal parts:
Front panel
Rear panel
left and right sides
main chassis
Preamp assembly w/ metal work
3 switch module on left side
S meter light and socket
Plastic PCB Holders
Offset pot
Drive pot
Selectivity rotary switch
Mode switch
Mic jack
Headphone Jack
Internal PC boards:
SWR / TR
T/R Relay
RF Trimmer
VFO Mixer / Oscillator
Low Level Driver
8 Pole Crystal Filter
Audio Amp
Low Pass Filter
SSB Generator
Attenuator
Maybe a few things not listed.
Please let me know what you need.
.
TenTec Century 21, Model 570 Parts For Sale:
I have parts from a Century 21, model 570, available.
Most of these parts should also fit the Model 574
digital version.
Hopefully these parts will let several rigs live again.
PTO, power supply parts, and final module are gone.
Available Parts:
Metal parts:
Inside front subpanel
Rear Panel
Both left and right sides
Main chassis
Large PS Filter Cap
Headphone Jack
3 pilot bulbs and sockets
Circuit Board Assemblies:
Control board 80355
Audio Power Amp 80357
Front end board 80359
Low Pass Filter 80360
Please let me know what you need.
.
TenTec Original Boxes
These are original boxes only,
and do not include the equipment.
Inserts are included.
TenTec AC-5 QRP Antenna Tuner $8
TenTec KR-2 Keyer Paddles $5
TenTec 255 PS $20
TenTec 561 Corsair $30
TenTec 604 Keyer Paddles $5
These are original boxes only.
.
I also have many other accessories available such as many
different types of microphones, HTs, VHF and UHF rigs, HF
and VHF/UHF antennas, connectors, miscellaneous accessories,
etc.
Just too many to list here. Please e-mail your requests.
.
Prices do not include shipping from Florida.
Thanks.
73,
Ken, W8EK
Ken Simpson
E-mail to W8EK@FLHam.net or W8EK@arrl.net
Voice Phone (352) 732-8400
.
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|