Byron,
Thanks for your reply. I have that board out of the rig already, and when my
wife quits bugging me (it's Valentine's day so I can't ignore her) I'll get to
checking that diode and whatever other components I can. I suspect it's
something like this as well.
--K4VBB
________________________________
From: TenTec <tentec-bounces+k4vbb=live.com@contesting.com> on behalf of Byron
Cordes via TenTec <tentec@contesting.com>
Sent: Monday, February 14, 2022 7:47 PM
To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Cc: Byron Cordes <byroncordes@icloud.com>
Subject: Re: [TenTec] Ten Tec Orion II problem -- will not power on
Hello
If voltage drops down to 5 volts is drawing a lot more than 6 amps Hihi
The only thing I can think of is Polarity protection diode. However I did
buy a Orion that the circuit board was toast next to the molex plug .
73s AC9PA Byron
On Feb 14, 2022, at 4:28 PM, Rod Greene via TenTec <tentec@contesting.com>
wrote:
Be very suspicious of the power connector at the back of the Orion. I had to
change mine for power poles. The connectors are well known for causing problems
like this.
73 and GL, Rod/w7zrc
On Monday, February 14, 2022, 01:55:17 PM MST, Marcus Florido
<k4vbb@live.com> wrote:
Thanks Bernard. I already have. I checked on 2 other power supplies with the
same result. The LCR also indicates that the repairs I made on the A9 board
are still sound. While I have checked continuity on the power connector, I'll
give it another look and make sure it has a GOOD connection. However, with the
observed amperage draw I suspect that the power connector is fine.
________________________________
From: TenTec <tentec-bounces+k4vbb=live.com@contesting.com> on behalf of
BERNARD SKOCH via TenTec <tentec@contesting.com>
Sent: Monday, February 14, 2022 3:36 PM
To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Cc: BERNARD SKOCH <k5xs@aol.com>
Subject: Re: [TenTec] Ten Tec Orion II problem -- will not power on
I would try another power supply and check the A9 board (it may have failed
after you rebuilt it).
I would also check the integrity of the power connector.
> On Feb 14, 2022, at 13:53, Marcus Florido <k4vbb@live.com> wrote:
>
> In October of last year I sent my Orion II to Ten Tec for a simple
> alignment. With the exception of a very minor alignment issue (perfect on
> 40m, 20Hz off on 10m), the rig functioned as it should when I sent it to the
> repair facility.
>
> I'm sure that by now we all know that the repair facility closed down in
> December, and my rig was shipped back to me by Ten Tec. While I thank Mike
> for taking care of this, and rejecting offers he received to buy the lot, I
> do have a complaint. My rig has come back to me in non-functioning condition.
>
> The rig won't power up. When plugged in to power only (no other connections)
> there is an awful buzzing noise when I flip the switch. The rig immediately
> draws around 6 amps and drops the voltage on an Astron RS-35M to about 5
> volts. Obviously I don't leave it in this condition, but the rig is now
> useless to me until I can figure out how to fix it and where to start.
>
> It might be important to note that I rebuilt the A9 board when I got
> it--worked perfectly when I sent it in.
>
> Has anyone else run into an issue like this?
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|