Using latest firmware, and already tried full reset.
Thanks
> On Mar 20, 2022, at 13:20, Onno PA1AP <pa1ap@nextchallenge.net> wrote:
>
> Most likely RX EQ, passband setting or Rx bandwidth. DSP bandwidth will
> drive selection of IF filters if configured through menu. Tx and Rx
> bandwidth work independently.
>
> Do you notice difference between lsb and usb signals?
>
> A master reset will return all values to factory default and might be the
> easiest step. Are you using the latest firmware?
>
> Regards Onno
>
> Op zo 20 mrt. 2022 17:00 schreef <tentec-request@contesting.com>:
>
>> Send TenTec mailing list submissions to
>> tentec@contesting.com
>>
>> To subscribe or unsubscribe via the World Wide Web, visit
>> http://lists.contesting.com/mailman/listinfo/tentec
>> or, via email, send a message with subject or body 'help' to
>> tentec-request@contesting.com
>>
>> You can reach the person managing the list at
>> tentec-owner@contesting.com
>>
>> When replying, please edit your Subject line so it is more specific
>> than "Re: Contents of TenTec digest..."
>>
>>
>> Today's Topics:
>>
>> 1. Orion 2 Receive Audio (Bernie Skoch)
>> 2. Re: Orion 2 Receive Audio (Barry Simpson)
>>
>>
>> ----------------------------------------------------------------------
>>
>> Message: 1
>> Date: Sun, 20 Mar 2022 00:20:16 +0000 (UTC)
>> From: Bernie Skoch <k5xs@aol.com>
>> To: "tentec@contesting.com" <tentec@contesting.com>
>> Subject: [TenTec] Orion 2 Receive Audio
>> Message-ID: <1034607059.993251.1647735616140@mail.yahoo.com>
>> Content-Type: text/plain; charset=UTF-8
>>
>> I have an Orion 2 that transmits great, but the receive audio bandpass
>> sounds very narrow.
>> I've verified the filters are behaving, and the receive width control is
>> set right.
>> Any clues?
>> TIA,
>> Bernie K5XS
>>
>> ------------------------------
>>
>> Message: 2
>> Date: Sun, 20 Mar 2022 14:42:34 +1100
>> From: Barry Simpson <vk2bj@optusnet.com.au>
>> To: Bernie Skoch <k5xs@aol.com>, Discussion of Ten-Tec Equipment
>> <tentec@contesting.com>
>> Subject: Re: [TenTec] Orion 2 Receive Audio
>> Message-ID:
>> <CA+03d8g0S0D=
>> A+BaKVQQvimT2LK6gUuLCSNL+MJKgA3SesUbHg@mail.gmail.com>
>> Content-Type: text/plain; charset="UTF-8"
>>
>> How have you set the audio settings - you may have too much treble
>> emphasis.
>>
>> Barry VK2BJ
>>
>> NB you say you have got the filter widths right. What exactly have you set
>> it at ? I have my audio at 2.8kHz on SSB and RX equalizer at -9db
>>
>>> On Sun, 20 Mar 2022 at 11:20, Bernie Skoch via TenTec <
>>> tentec@contesting.com>
>>> wrote:
>>>
>>> I have an Orion 2 that transmits great, but the receive audio bandpass
>>> sounds very narrow.
>>> I've verified the filters are behaving, and the receive width control is
>>> set right.
>>> Any clues?
>>> TIA,
>>> Bernie K5XS
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>
>>
>>
>> ------------------------------
>>
>> Subject: Digest Footer
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>>
>> ------------------------------
>>
>> End of TenTec Digest, Vol 231, Issue 9
>> **************************************
>>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|