Hi Frank,
Thank you very much for your detailed reply. As I noted, I
don’t have a FT 1000MP but I will pass along your email to Andy and I know he
will very much appreciate hearing from someone like yourself. As I said once
at a Contest University session, I’ll stay and listen to Frank as long as he’s
willing to talk.
73 Kip W6SZN
From: donovanf@starpower.net [mailto:donovanf@starpower.net]
Sent: Wednesday, June 15, 2016 8:30 AM
To: Top Band Contesting; PVRC Submissions
Subject: Re: Topband: FT-1000MP
Hi Kip,
Your question involves perhaps the most frequently misunderstood
aspect of FT-1000MP receiver operation, a result of the poorly
written description of Menu 8-4 on page 91 of the operating
manual. A much better description and illustration of pre-amplifier
selection menu 8-4 and the IPO front panel push button appears
on page 30 of the operating manual.
Two controls must be properly set to optimize FT-1000MP receiver
front-end performance on 160, 80 and 40 meters: Attenuator and
IPO. When IPO is enabled, it bypasses the pre-amplifier selected
by Menu 8-4.
The FT-1000MP has three pre-amplifiers:
- a 1.8 - 7 MHz pre-amplifier (IPO should be enabled when
operating on 160, 80 and 40 meters to bypass this pre-amplifier)
- a pre-amplifier with excellent sensitivity on 24 and 28 MHz
- a wideband (FLAT) pre-amplifier with very poor 28 MHz sensitivity
The front panel IPO pushbutton bypasses the pre-amplifiers entirely,
feeding the antenna directly into the first mixer. I always enable
IPO when operating on 160, 80 and 40 meters.
The Attenuator should be set to the highest setting while providing
acceptable receiver sensitivity. I almost always set the attenuator
to 18 dB when operating on 160 meters.
I always set Menu 8-4 to TUNED, allowing the FT-1000MP to
automatically select the proper pre-amplifier for 12 and 10 meters,
I never use the 1,8-7 MHz preamplifier because I always enable
IPO when operating on those bands and I never set Menu 8-4 to FLAT.
73
Frank
W3LPL
_____
From: "Kip Edwards" <kedwards@ltol.com>
To: "Top Band Contesting" <topband@contesting.com>
Sent: Wednesday, June 15, 2016 2:07:09 PM
Subject: Topband: FT-1000MP
All,
I have been corresponding via email with Andy, SP6AEG,
regarding the 5J0P DXpedition and other topics. This morning I received the
following question from Andy:
"I received from Janusz SP6IXF as gift transceiver FT1000MP with a set of
filters in optional (2 kHz / 250 Hz) ssb / cw + roofing filter. I have a
dilemma, do not know who Receiver Front-End RF Amplifier should be active
for optimal performance for 160 m. I have a choice of flat or Tuned for low
band. Do you have on this subject some knowledge?"
Is there anyone on this reflector who can offer any help? I
know nothing about the
FT 1000MP (among many other things) but I'd like to help Andy.
Many thanks.
73 Kip W6SZN
G. Kip Edwards
Telephone: (206) 999-9403
email: kedwards@ltol.com
NOTICE: This E-mail (including attachments) is covered by the Electronic
Communications Privacy Act, 18 U.S.C. 2510-2521, is confidential and may be
legally privileged. Information contained in this e-mail message is intended
only for the individual to whom it is addressed and is private and
confidential. If you are not the intended recipient, or the employee or
agent responsible for delivering this message to the intended recipient, any
dissemination, distribution or copying of this communication is strictly
prohibited. If you are not the intended recipient of this e-mail, please
kindly destroy it and notify the sender immediately by reply e-mail. Please
take standard precautions to mitigate virus issues. Thank you for your
cooperation.
_________________
Topband Reflector Archives - http://www.contesting.com/_topband
_____
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2016.0.7639 / Virus Database: 4598/12406 - Release Date: 06/12/16
_________________
Topband Reflector Archives - http://www.contesting.com/_topband
|