Reflector problems this is what I wanted to say. 73 Clive GM3POI
From: Clive GM3POI [mailto:clive@gm3poi.com]
Sent: 05 December 2018 16:17
To: 'MU 4CX250B'
Subject: RE: Topband: new style PL-259's with screw on back INSTRUCTIONS
Well here the RF connection Brass / silver plated have been bought by the dozen
over the years. The Compression type whilst coming in handy in poor weather is
not the plug of choice here and I’ve tried them for many years. On the
compression plugs you should also drill out the centre conductor hole otherwise
a typical RG213 type cable will not get to the tip of the plug to be soldered.
Designed by an idiot I suspect. 73 Clive GM3POI
From: MU 4CX250B [mailto:4cx250b@miamioh.edu]
Sent: 05 December 2018 16:04
To: Clive GM3POI
Cc: topband@contesting.com
Subject: Re: Topband: new style PL-259's with screw on back INSTRUCTIONS
Finally, after years of frustration with several types of PL259 connectors,
I've settled on the new crimp/solder type from DX Engineering. They're strong,
reliable, and easy to install in minutes while dangling from a tower. Soldering
is only for the center conductor.
The downsides are that they're a bit pricey, and require a crimp connector.
Over the past year, I've bought about fifty of them and am gradually swapping
them into all my indoor and outdoor cables. Here's a link:
https://www.dxengineering.com/parts/dxe-pl259cs8x-12
BTW, I'm also phasing out all the LMR-400 (both the ordinary and superflex
types) in my station and going back to plain old RG213. The modest attenuation
improvement of LMR400 over the earlier RG--type cables is negligible at HF
frequencies, and the Al foil and awkward-size center conductor of the LMR
cables have been, for me, nothing but trouble.
73,
Jim W8ZR
Sent from my iPhone
On Dec 5, 2018, at 8:27 AM, Clive GM3POI <clive@gm3poi.com> wrote:
I have been using those plugs for at least 10 years. They come in useful if
you have to put on a plug in cold weather and or high winds because no braid
soldering is needed. However at the back of equipment they are more
temperamental than regular 259's because the threads tend to be difficult.
YMMV
73 Clive GM3POI
-----Original Message-----
From: Topband [mailto:topband-bounces@contesting.com] On Behalf Of MICHAEL
ST ANGELO
Sent: 05 December 2018 14:49
To: Pete Michaelis - N8TR; topband@contesting.com
Subject: Re: Topband: new style PL-259's with screw on back INSTRUCTIONS
These are compression connectors similar to the N type compression
connector.
I use them as well as crimp type UHF connectors because I don't like the
solder type PL259 connectors for RG-8. RG-58 or LMR-400 type coax.
Pasternack offers a similar type connector. Their data sheet has assembly
instructions. You can use it as a guide.
<https://www.pasternack.com/images/ProductPDF/PE44050.pdf>
Mike N2MS
On December 5, 2018 at 12:34 AM Pete Michaelis - N8TR
<pete.n8tr@gmail.com> wrote:
EBAY item 192225630585 looks similar to the Multicomp clamp
connector discussed on
Towertalk early in 2011. See:
http://lists.contesting.com/_towertalk/2011-02/msg00214.html
73, Pete - N8TR
At 09:45 PM 12/4/2018, terry burge wrote:
Hi Gary
Take a look at ebay 'UHF PL259 male clamp Plug lot connector for
LMR400 RG8 RG213 RG214 Coax cable' from 'superstore_dan'.
Terry
KI7M
_________________
Searchable Archives: http://www.contesting.com/_topband - Topband
Reflector
_________________
Searchable Archives: http://www.contesting.com/_topband - Topband Reflector
---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
_________________
Searchable Archives: http://www.contesting.com/_topband - Topband Reflector
_________________
Searchable Archives: http://www.contesting.com/_topband - Topband Reflector
|