I use NCC-1 and NCC-2 boxes for phasing numerous receive antennas, mostly on
160. My property is heavily wooded, with antennas among loblolly pines, oak,
maple, gum, etc.
For in-band listening while transmitting on 160, I have a pair of 34-foot
verticals (self-supporting aluminum elements) placed about 1000 feet from my
nearest transmit array, roughly on a line toward Europe (the RX antennas are
closer to Europe). Spacing is 1/4 wave. To get maximum end-fire null, they are
lined up on a heading of 29 degrees. The beamwidth is broad enough to hear many
Eu signals while transmitting. Equal RG6 feedlines run to an NCC-1 in the
shack, and I am able to listen within a few kHz of my transmit signals
The quality of the transmitter signal and the receiver are major factors
allowing in-band listening. There was a quantum leap years ago when I upgraded
my K3's to the newer synthesizer boards (or a K3S).
When I change directions of the transmit array, I usually have to tweak the
null on the NCC-1.
I also have used a broadside/endfire set of 560-ft Beverages that have the TX
array off the rear for in-band listening and their null is deep enough for this
to work. I use an NCC-1 to phase the two pairs of Beverages. The closest
feedpoint is about 550 feet from the nearest TX array.
I have two sets of broadside-endfire short verticals (four 34-foot wire
elements hung from trees). These have the two forward and rearward element
feedlines coming together at tees (no matching) and then separate feeds run to
an NCC-2 in the shack. Performance of these can equal or exceed that of the
numerous phased Beverages we have.
A few of my stagger-phased Beverages have separate feedlines going to an NCC-1.
This allows adjusting the rearward null for optimum.
While the exact phase setting isn't known, the settings achieved experimentally
are repeatable. I use several BC stations in the 1600-1700 range for
reference.; An S-9 plus signal often will drop out entirely when I reverse the
phase on the NCC-1 (or -2).
The charts of phased arrays in the ARRL Antenna Book and ON4UN's Low Band
antennas book are useful in positioning of the various arrays for placing the
null in a desired direction.
73/Jon
Jon P. Zaimes, AA1K
Tower climber for hire
Felton, Delaware
http://www.aa1k.us/
Reviews of AA1K tower work on eham website:
http://www.eham.net/reviews/detail/12922
Hug your favorite tower every day, and always stay connected to it.
On Saturday, December 16, 2023 at 10:05:41 PM EST, Kenny Silverman
<kenny.k2kw@gmail.com> wrote:
Rick, my application is for an in-band RX antenna, but on a higher band. I
just thought the guys here might know more about the NCC-2, MFJ or QRM
eliminator than most others.
One thought was to create a 2 ele phased vertical array for the RX antenna
with a known pattern and put the null towards the TX array, along with
physical separation to allow in-band receiving.
But I was thinking an adjustable phasing system may produce a better null.
But I wouldn’t want the adjustable unit to create a clover leaf pattern for
example. One null might take out the interference but another null towards
the desired receiving direction might be created and is not desired.
I hope I’m explaining this well.
Regards , Kenny K2KW
> On Dec 16, 2023, at 9:47 PM, Rick Kunath <k9ao@yahoo.com> wrote:
>
> What's your application Kenny and what would you be feeding the antenna
> output of the phaser into?
>
> Rick Kunath, K9AO
>
_________________
Searchable Archives: http://www.contesting.com/_topband - Topband Reflector
_________________
Searchable Archives: http://www.contesting.com/_topband - Topband Reflector
|