[Top] [All Lists]

[TowerTalk] Rohn HDBX Tower - Boom Length

To: <>
Subject: [TowerTalk] Rohn HDBX Tower - Boom Length
From: (
Date: Tue, 3 Feb 1998 13:46:34 -0500
Unless you are looking for a quick, cheap installation because you arent
going to be there very long, I'd stay away from the BX series towers.  Like
Steve says, the are stamped diagonals and they use aluminum rivets.  They
will not withstand a lot of torque.  In addition, the galvanization is
rather cheap and a fter a few years, you'll have a lot of rust unless you
paint the whole thing (which would probably almost double the weight of the
tower!)  You cant regalvanize BX tower either because of the aluminum
rivets.  I'm not convinced there isnt a lot of potential for noise from the
tower because of the dissimilar metals involved, although that would
probably be a few years down the road.  If it has to be self supporting
with anything bigger than a TH6, I'd look at some SSV tower or perhaps some
bracketed Rohn 45 if you have a nice high roofline.  That would be a much
longer term investment to be sure...

73, Ty K3MM on 02/03/98 01:25:12 PM

cc:    (bcc: Tyler G Stewart/BENN/CEC)
Subject:  Re: [TowerTalk] Rohn HDBX Tower - Boom Length

In a message dated 98-02-03 12:46:35 EST, writes:
> <<     While on BX tower, the HDBX is supposed to take 18 square feet
with a
>   maximum boom length of 10 feet.  What kind of a ham antenna has those
>   specifications (other than a dish)?  But Rohn lists them in their "Ham
>   Catalog" and several well known ham dealers advertise them in QST and
>   magazines, obviously saying they are intended for ham use.  What "ham
>   is consistent with the 18 square foot and 10 foot boom specifications?
>    >>
     How about a nifty VHF/UHF installation? Since the BX series was
for TV antenna applications, this isn't too far off.
     The problem with BX is that the legs are stamped (not round like 25G,
etc.) and the X-braces do not overlap. This structure has little torsional
resistance, hence the "maximum 10 foot boom" warning.
    Don't forget that the top sections of the BX, HBX and HDBX are all
different (look it up in your Rohn catalog for more info). Obviously the
top section for the HDBX is sturdier than the BX-1 or BX-2 on the others.
>  Funny that Stan should comment on this anomoly.  I am considering the
> erection
>  of a 48-foot HDBX tower.  In its self-supporting configuration, it is
>  supposed to take 18 square feet of antenna with maximum boom length of
>  feet.  I would like to put up a Force 12 C-4XL (9.6 square feet, 30 foot
> boom)
>  or, second choice, a C-4SXL (8.4 square feet, 23 foot boom).  The square
>  footage doesn't seem to be an issue, but the boom length of either
> is
>  of concern.
      An HDBX-48 tower is STRONG and I wouldn't be afraid of  putting the
aforementioned system on it. My experience is that it'll take medium sized
loads as well.
    The second caveat with BX is that the top plate and rotator plate are
small gauge sheet metal. They won't take the constant torque from a large
system either. I've got a 4 year old HDBX in my bone yard that had a PRO67
it (NOT mine!). Both of the plates are cracked and need replacing. Beefing
them up will buy you some additional reliability but these towers have
>  As Stan comments, the value of this reflector is in gathering empirical
>  evidence.  So I seek specific examples of what antennas any of you have
> on
>  an HDBX tower (square footage and boom length), what wind speeds have
>  experienced, and how the tower stood up under those conditions.
      Phil, Tarrant county is a 70 MPH wind speed zone, the lowest rating
given. That's the same wind speed used for the BX towers. For your proposed
system and wind speed, my recommendation is to go for it. You won't have
problems in the foreseeable future. BTW, the reduced weight and windload of
the Force 12 antennas are beneficial to this and any tower system.
    I would take any direct experiences with a grain of salt. Some people
been amazingly lucky in overloading their system with no failure (K7LXC
visibly shuddering). Be conservative and you'll be fine. Exceeding the
manufacturer's boom length spec in this case of an HDBX-48 is one of the
times where I recommend something other than following the manufacturer's
specs. In ALL other cases, DO what the manufacturer says!
73,  Steve  K7LXC
     TOWER TECH -- professional tower supplies and services for amteurs
FAQ on WWW:     
Administrative requests:

FAQ on WWW:     
Administrative requests:

<Prev in Thread] Current Thread [Next in Thread>