This is a multi-part message in MIME format.
------=_NextPart_000_0082_01BDE59B.F15960A0
Content-Type: text/plain;
charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable
When one has preamps for V/UHF on the same tower as QRO HF antennas, =
must one take any special precautions to keep the high power HF out of =
the preamps?=20
I am planning a single-tower installation with some kind of HF Yagi plus =
144 MHz, 435 MHz and 900 MHz parasitic arrays. I'm also thinking of =
feeding the HF Yagi boom on 40 Meters. I expect to have preamps for all =
3 V/UHF bands in the feedlines (for ATV and weak-signal 2-M work), with =
the preamps mounted near the top of the tower. =20
I understand from N4KG that I could measure coupled power with a =
Wattmeter at the end of each coax jumper, before it enters its =
respective preamp (Thanks again, Tom). But that means I would have =
already spent the $$ for the V/UHF arrays and might not be able to use =
them. Plus, putting high-pass filters before the preamps will have an =
impact on the noise figure of the array on receive.
Does anyone have experience in using V/UHF preamps with HF arrays as =
I've described? Thanks
-Gene Smar AD3F
------=_NextPart_000_0082_01BDE59B.F15960A0
Content-Type: text/html;
charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable
<!DOCTYPE HTML PUBLIC "-//W3C//DTD W3 HTML//EN">
<HTML>
<HEAD>
<META content=3Dtext/html;charset=3Diso-8859-1 =
http-equiv=3DContent-Type>
<META content=3D'"MSHTML 4.72.2106.6"' name=3DGENERATOR>
</HEAD>
<BODY bgColor=3D#ffffff>
<DIV>When one has preamps for V/UHF on the same tower as QRO HF =
antennas, must=20
one take any special precautions to keep the high power HF out of the =
preamps?=20
</DIV>
<DIV> </DIV>
<DIV>I am planning a single-tower installation with some kind of HF Yagi =
plus=20
144 MHz, 435 MHz and 900 MHz parasitic arrays. I'm also thinking =
of=20
feeding the HF Yagi boom on 40 Meters. I expect to have preamps for all =
3 V/UHF=20
bands in the feedlines (for ATV and weak-signal 2-M work), with the =
preamps=20
mounted near the top of the tower. </DIV>
<DIV> </DIV>
<DIV>I understand from N4KG that I could measure coupled power with a =
Wattmeter=20
at the end of each coax jumper, before it enters its respective preamp =
(Thanks=20
again, Tom). But that means I would have already spent the $$ for =
the=20
V/UHF arrays and might not be able to use them. Plus, putting =
high-pass=20
filters before the preamps will have an impact on the noise figure of =
the array=20
on receive.</DIV>
<DIV> </DIV>
<DIV>Does anyone have experience in using V/UHF preamps with HF arrays =
as I've=20
described? Thanks</DIV>
<DIV> </DIV>
<DIV> </DIV>
<DIV>-Gene Smar AD3F</DIV></BODY></HTML>
------=_NextPart_000_0082_01BDE59B.F15960A0--
--
FAQ on WWW: http://www.contesting.com/towertalkfaq.html
Submissions: towertalk@contesting.com
Administrative requests: towertalk-REQUEST@contesting.com
Problems: owner-towertalk@contesting.com
Search: http://www.contesting.com/km9p/search.htm
|