Towertalk
[Top] [All Lists]

[TowerTalk] Tuning coax stubs w/ shack test equipment

To: <towertalk@contesting.com>
Subject: [TowerTalk] Tuning coax stubs w/ shack test equipment
From: ken.r.mason@intel.com (Mason, Ken R)
Date: Tue, 30 Mar 1999 10:48:03 -0800
Hello Fellow Hams,

I had tried to work with stubs to prevent intermod during a VHF contest.
Station consisted of 1500 watts on 6M and 1500 watts on 2M. Of course the 6M
station was killing the 2M receiver. I made a 19 inch approx. 1/2 inch
hard-line shorted stub and put it on the 2M radio using a tee connector.

The results were poor. The 2M radio worked fine but the 6M signal still got
in. Checking it with the mfj 259 showed it was super wide. using a tee
connector with a dummy load and the shorted stub showed about 40 ohms on 6M
using the mfj 259.

Is this to be expected? I need to remove the intermod signals on my 2M and
432 radios. Any ideas for my single tower contest station? ( no, not another
tower)

73,
Ken
KC6TEU
mailto:ken.r.mason@intel.com
http://www.qsl.net/kc6teu/
http://home.earthlink.net/~kmcm/
 

-----Original Message-----
From: k6ll@juno.com [mailto:k6ll@juno.com]
Sent: Monday, March 29, 1999 9:13 PM
To: towertalk@contesting.com
Subject: Re: [TowerTalk] Tuning coax stubs w/ shack test equipment





On Mon, 29 Mar 1999 18:36:15 -0800 Steve Gehring / KL7DC
<gehring@alaska.net> writes:

> I grabbed an "odd" piece of coax (128 inches of 
>cheap
>RG-11) from the shack closet and connected it to my Autek RF-1.  For 
>the
>open stub test, the impedance bottomed out at 15.05 MHz with 7 ohms, 
>and
>only rose to 13 ohms at 14.05 MHz, or 1 MHz lower.....

> Now, my Autek worked fine for this 
>application,
>and made finding the center of that low Q, broad notch and/or 
>passband
>rather uneventful.  I've never used an MFJ, but would guess the SWR 
>would
>peak during the stub's electrical shorts and opens.  I feel they are a 
>good
>way to check your work, especially with possibility of length
>miscalculations and varying velocity factors, etc.  

I didn't see the original posting on this, but something is wrong
here. A 10' stub made out of rg-8 or rg-11 should have an impedance
minimum of about 0.5 ohm. I just tested my 40m shorted stub, made out
of rg-8, and it read 0 ohms from 14.0 to 14.7 Mhz on the Autek
meter. This is a false reading, though, because of the "diode
suck-out" problem discussed in the Autek manual for very low impedance
measurements. 

I still think the best way to tune a stub is to
beg, borrow, steal or buy a grid dip meter, temporarily connect a
1 inch piece of wire from the pin to shell of the stub's pl-259,
and couple the gdo into the small square loop formed by the little
wire, the pin, and the shell of the pl-259.

Dave Hachadorian, K6LL
Yuma, AZ
K6LL@juno.com





















___________________________________________________________________
You don't need to buy Internet access to use free Internet e-mail.
Get completely free e-mail from Juno at http://www.juno.com/getjuno.html
or call Juno at (800) 654-JUNO [654-5866]


--
FAQ on WWW:               http://www.contesting.com/towertalkfaq.html
Submissions:              towertalk@contesting.com
Administrative requests:  towertalk-REQUEST@contesting.com
Problems:                 owner-towertalk@contesting.com
Search:                   http://www.contesting.com/km9p/search.htm


--
FAQ on WWW:               http://www.contesting.com/towertalkfaq.html
Submissions:              towertalk@contesting.com
Administrative requests:  towertalk-REQUEST@contesting.com
Problems:                 owner-towertalk@contesting.com
Search:                   http://www.contesting.com/km9p/search.htm


<Prev in Thread] Current Thread [Next in Thread>