Towertalk
[Top] [All Lists]

[Towertalk] Knots

To: <towertalk@contesting.com>
Subject: [Towertalk] Knots
From: w5lu@hotmail.com (S. J. Blackwell)
Date: Mon, 23 Dec 2002 05:08:37 +0000
Add to that the rolling hitch and you need nothing else.
73
Sam Blackwell, W5LU  late of SY "World Enough"






>From: "Michael Walker" <va3mw@rogers.com>
>Reply-To: "Michael Walker" <va3mw@rogers.com>
>To: <towertalk@contesting.com>
>Subject: Re: [Towertalk] Knots
To: <towertalk@contesting.com>
>Date: Sun, 22 Dec 2002 23:40:24 -0500
>
>After 3 Worrell 1000's, lots of Keel boat racing over the past 20 years (am
>I that old??), etc., I've also NEVER seen a bowline undo, unless it was on
>very inexpensive nylon rope.  A half-hitch on the loose end prevented that.
>
>Learn it, the reef knot, a clove hitch, and the sheet bed (see
>http://131.230.57.1/knots.htm) and you will be set for life.  Make sure you
>understand the role of each knot.  A figure 8 is also very handy to know.
>
>Mike VA3MW
>----- Original Message -----
>From: "Dale L Martin" <kg5u@hal-pc.org>
>To: <towertalk@contesting.com>
>Sent: Saturday, December 21, 2002 11:28 AM
>Subject: RE: [Towertalk] Knots
>
>
> >
> > To continue the sea stories subthread, I crewed on a Cal-40 racing in
> > Galveston Bay and the Gulf of Mexico for about 15 years.  I don't recall 
>a
> > bowline ever working itself loose on our boat.  I don't even remember
>anyone
> > checking before tacking.  When on a tack, the windward sheet (line) is
>slack
> > and tension is off that bowline knot at the genoa clew while the leeward
> > sheet has the strain.
> >
> > Out in the Gulf, there were opportunities for being on one tack for 
>hours
> > and hours, even days (Galveston-Vera Cruz race).
> >
> > I think that if there was a concern about the bowline going loose and
> > possibly letting go, it wouldn't have been used or we would have done
> > something to preclude it.
> >
> > Maybe the conditions onboard weren't conducive to knot loosening.
> >
> > Under exactly what conditions will an unloaded bowline knot become 
>loose?
> >
> > 73,
> > dale, kg5u
> >
> > >
> > > You're close.  The only problem with a bowline is that if it's under
> > > no load, it tends to loosen.  You can make it more secure in various
> > > ways.  I believe that it is one of the good knots that maintains more
> > > of the strength of the line.  OTOH, the figure-eight loop is easily
> > > tied, even in the middle of the line and seems to stay tight, but
> > > loses more of the inherent line strength, and perhaps as the obverse
> > > of the above, is hard to untie.  Many of us think a knot should be
> > > easily untied.
> > >
> > > BTW, I've seen figures that indicate an eye splice is actually
> > > stronger than the line, and a cunt splice is the absolute strongest
> > > way of fastening two laid lines together.  But I still don't know how
> > > to make an eye splice in the braided lines I like.
> > >
> > > 73, doug
> >
> > _______________________________________________
> > AN Wireless Self Supporting Towers at discounted prices,
> > See http://www.mscomputer.com
> >
> > Wireless Weather Stations now $349.95. Call Toll Free,
> > 888-333-9041 for additional information.
> > _______________________________________________
> > Towertalk mailing list
> > Towertalk@contesting.com
> > http://lists.contesting.com/mailman/listinfo/towertalk
> >
>
>_______________________________________________
>AN Wireless Self Supporting Towers at discounted prices,
>See http://www.mscomputer.com
>
>Wireless Weather Stations now $349.95. Call Toll Free,
>888-333-9041 for additional information.
>_______________________________________________
>Towertalk mailing list
>Towertalk@contesting.com
>http://lists.contesting.com/mailman/listinfo/towertalk


_________________________________________________________________
MSN 8: advanced junk mail protection and 3 months FREE*. 
http://join.msn.com/?page=features/junkmail&xAPID=42&PS=47575&PI=7324&DI=7474&SU=
 
http://www.hotmail.msn.com/cgi-bin/getmsg&HL=1216hotmailtaglines_advancedjmf_3mf


<Prev in Thread] Current Thread [Next in Thread>