Towertalk
[Top] [All Lists]

Re: [TowerTalk] M2 OR-2800 Rotor Stuck

To: <TOWERTALK@contesting.com>
Subject: Re: [TowerTalk] M2 OR-2800 Rotor Stuck
From: "Julio Peralta" <jperalta@tampabay.rr.com>
Date: Fri, 5 Nov 2004 08:52:19 -0500
List-post: <mailto:towertalk@contesting.com>
Bob can you explain why the controller had to go back 3 times. We have just
purchased one for our radio club and would like to know what problems you
have had.

Julio, W4HY

----- Original Message ----- 
From: "w9ge" <finger@goeaston.net>
To: <k1ir@designet.com>
Cc: <towertalk@contesting.com>
Sent: Friday, November 05, 2004 8:13 AM
Subject: Re: [TowerTalk] M2 OR-2800 Rotor Stuck


> Jim:  tells me probably your pulse leads are not delivering the pulses
from
> the rotator to the controller box, or the MOV took a hit.    check all
> connections between pins 5/6 and the rotator unit.  There is a
> troubleshooting guide in the manual.  If you have no manual, let me know
and
> I will regurgitate them for you.  You can lift the MOV from the pin inside
> the controller unit also to check that.
>
> If all else fails, then you can still turn the beam.  Hook up a sturdy
12vdc
> supply or battery to leads one and two.  Watch which way the beam turns,
and
> reverse polarity if you wanna go the other way.  You cannot hurt the
rotator
> motor doing it this way.
>
> I have one 2800 controller that has been back to m2 three times in the
last
> year. Whenever it is gone, I use a 20 amp 12vdc supply to turn the beam by
> the eyeball method.  Not elegant but beats being stuck in one direction.
> Good luck.  73 bob de w9ge
> ----- Original Message ----- 
> From: <k1ir@designet.com>
> To: <>; <yccc@yccc.org>
> Cc: <k1ir@designet.com>
> Sent: Thursday, November 04, 2004 10:07 PM
> Subject: [TowerTalk] M2 OR-2800 Rotor Stuck
>
>
> > Just came into the shack to test out the rig and see if things are
working
> > for SS this weekend. The OR-2800 is pointing at 328 deg, and the
indicator
> > reads correctly, but when instructed to move, it just stays there. Same
> > thing in any mode - direct, variable or fixed preset. This has never
> > happened here before. Everything was working fine over the weekend.
> > Anybody seen this behavior? This is the DC model. Please email me direct
> > if you have any ideas. The weather is bad here and I was hoping to turn
> > the antennas to deal with expected high winds on Friday.
> >
> > 73,
> >
> > Jim K1IR
> >
> > _______________________________________________
> >
> > See: http://www.mscomputer.com  for "Self Supporting Towers", "Wireless
> > Weather Stations", and lot's more.  Call Toll Free, 1-800-333-9041 with
> > any questions and ask for Sherman, W2FLA.
> >
> > _______________________________________________
> > TowerTalk mailing list
> > TowerTalk@contesting.com
> > http://lists.contesting.com/mailman/listinfo/towertalk
> >
>
> _______________________________________________
>
> See: http://www.mscomputer.com  for "Self Supporting Towers", "Wireless
Weather Stations", and lot's more.  Call Toll Free, 1-800-333-9041 with any
questions and ask for Sherman, W2FLA.
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>


_______________________________________________

See: http://www.mscomputer.com  for "Self Supporting Towers", "Wireless Weather 
Stations", and lot's more.  Call Toll Free, 1-800-333-9041 with any questions 
and ask for Sherman, W2FLA.

_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>