Towertalk
[Top] [All Lists]

RE: [TowerTalk] PL-259 Soldering temperature

To: "'TowerTalk'" <towertalk@contesting.com>
Subject: RE: [TowerTalk] PL-259 Soldering temperature
From: "Keith Dutson" <kjdutson@earthlink.net>
Reply-to: keith@dutson.net
Date: Tue, 25 Jan 2005 20:48:01 -0600
List-post: <mailto:towertalk@contesting.com>
Now at home, found the one we took is P2K Portasol.  Also have the larger
WPA2 Pyropen.  That one sounds like a jet taking off when igniting.

Keith NM5G

-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] On Behalf Of W3YY
Sent: Tuesday, January 25, 2005 6:46 PM
To: TowerTalk
Subject: Re: [TowerTalk] PL-259 Soldering temperature

To All -

I've used a Weller Catalog No. WPA2 "Pyropen" successfully for years.  I
don't solder outside unless absolutely necessary, but this iron has done the
job for me on PL-259's and smaller jobs.  It's a wonderful outdoor soldering
tool.

73, Bob - W3YY


----- Original Message -----
From: "Keith Dutson" <kjdutson@earthlink.net>
To: "TowerTalk" <towertalk@contesting.com>
Sent: Tuesday, January 25, 2005 2:24 PM
Subject: RE: [TowerTalk] PL-259 Soldering temperature


I took a Weller propane iron kit on the VP8WWW DXpedition.  I don't remember
the model number but it was about $50 from the 'net and came with a variety
of tips/attachments.  It performed quite well although we did not try it on
any PL259 connectors.  The iron has a heat range controlled by a valve and
we had it set to about half way.  I think it would work on a PL259 but would
be quite difficult in windy conditions.

Keith NM5G/VP8DXL

-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] On Behalf Of Red
Sent: Monday, January 24, 2005 10:03 PM
To: TowerTalk
Subject: Re: [TowerTalk] PL-259 Soldering temperature

Hi, Gang;

Any experience or advise on using a propane heated soldering tip for
soldering the PL-259?  I'm referring to the rather heavy tips, 1/4 or 3/8"
diameter.  They can be custom made for extra mass and to mate the job.  They
tend to get too hot and burn the flux if the propane is turned on full.
Should they be filed to fit the curve of the connector or to fit into the
hole?

73 de WOØW

_______________________________________________

See: http://www.mscomputer.com  for "Self Supporting Towers", "Wireless
Weather Stations", and lot's more.  Call Toll Free, 1-800-333-9041 with any
questions and ask for Sherman, W2FLA.

_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________

See: http://www.mscomputer.com  for "Self Supporting Towers", "Wireless 
Weather Stations", and lot's more.  Call Toll Free, 1-800-333-9041 with any 
questions and ask for Sherman, W2FLA.

_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk


_______________________________________________

See: http://www.mscomputer.com  for "Self Supporting Towers", "Wireless
Weather Stations", and lot's more.  Call Toll Free, 1-800-333-9041 with any
questions and ask for Sherman, W2FLA.

_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________

See: http://www.mscomputer.com  for "Self Supporting Towers", "Wireless Weather 
Stations", and lot's more.  Call Toll Free, 1-800-333-9041 with any questions 
and ask for Sherman, W2FLA.

_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>