Steve, in order to apply the Prelube safely, I assume you would use a
ladder and spray it on that portion of the cable that is unspooled when
the tower is retracted? Then spray the remainder of the cable while it
is spooled onto the drum or while in the process of elevating the
tower? I just want to be sure I have this right.
73, Joe
K7LXC@aol.com wrote:
>> I am a relatively new crank-up owner (1 year) and have been following the
>>
>>
>thread on crank-ups. Jim's post on "crank-up use and winter maintenance"
>begs the questions of:
>a. What do you lubricate the sliding surfaces with?
>b. What should be used to lubricate the cable.
>
>Howdy, TowerTalkians --
>
> Here's the lowdown on crank-ups and maintenance.
>
> Several people have mentioned using PreLube 6 on the cables - that is
>correct. DO NOT use a grease or anything else that'll coat the cables. If you
>do that, the moisture can't escape and it'll rust from the inside out.
>PreLube
>6 soaks into the strands lubricating them and doesn't leave any residue on
>the outside of the cables that'll attract any crud or pollutants that'll
>stick
>to the cables. BTW _www.championradio.com_ (http://www.championradio.com)
>has the PreLube 6. It's what is specified by wire rope (cable) manufacturers.
>
> The PreLube is pretty thin and will wash out after awhile so an annual
>or semi-annual application will be real helpful. Start at the top of the
>tower
>and work your way down. It's pretty messy so you don't want to be climbing
>up and down the tower doing this.
>
> Don't worry about the pulleys. Modern ones (i.e. US Towers) have sealed
>bearings so you don't have to do anything with them. It's difficult
>(impossible?) to lube older pulleys that don't have sealed bearings so either
>way
>there's not much you can do.
>
> The bearings can freeze up so a good thing to do is to paint a mark on
>each one of them that you can see from the ground and then watch them when
>the
>tower is moving to make sure that they're turning. Obviously one that isn't
>turning is a problem.
>
> As far as the motor drive mechanism, use a little grease gun on all the
>grease nipples (zerk fittings) including the thrust bearing and keep
>squirting it in until new grease starts coming out.
>
> There are a couple of things you can do to prolong your cable life
>besides lubing it properly. One is to exercise it occasionally; that is, run
>it up
>and down a couple of times a month to, literally, work the kinks out. The
>other thing is to not always park it in the same spot when extended or
>lowered,
>usually where the limit switches are. If you do that, there's a good chance
>the cables can take a set over time where they go over the pulleys. Leaving
>it parked at different heights just about eliminates this potentially fatal
>problem. ("Taking a set" means that the cable will be permanently deformed at
>a
>point where it goes over a pulley.)
>
> As far as lubricating the sliding surfaces, I wouldn't worry about it.
>The factory used to use a real sticky grease when assembling the tower, now
>they just use paraffin. This makes it easier to slide the sections during
>assembly but there's no easy or safe way to do it when it's standing
>vertically in
>use. What material are you going to use and how will you apply it? You'd
>have to do it when the tower is extended and that's definitely NOT
>recommended
>since you'd have to have your fingers in there to do it. A spray material
>won't last very long so trying to lube the legs isn't worth it IMO.
>
> Crank-ups require more care and attention but doing all of the above
>will prolong the service life of the tower.
>
>Cheers,
>Steve K7LXC
>TOWER TECH -
>Professional tower services for commercial and amateur
>Cell: 206-890-4188
>_______________________________________________
>
>
>
>_______________________________________________
>TowerTalk mailing list
>TowerTalk@contesting.com
>http://lists.contesting.com/mailman/listinfo/towertalk
>
>
>
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|