Towertalk
[Top] [All Lists]

Re: [TowerTalk] Restringing Cable on Crankup Tower

To: "Russell Hill" <rustyhill@earthlink.net>,"Harry Williams" <willisw200@msn.com>,"Dino Darling" <dino@k6rix.com>
Subject: Re: [TowerTalk] Restringing Cable on Crankup Tower
From: "Byron Lichtenwalner" <w3wkr@verizon.net>
Date: Fri, 07 Sep 2007 11:01:56 -0400
List-post: <mailto:towertalk@contesting.com>
Hi Russwll
The answer to your question is YES.
I bought a set for my LM354.  One fit perfectly, the second was WAY too long 
and I had to shorten it.

At the time the cables were ordered in Sept. and arrived the next May!

Byron, W3WKR
----- Original Message ----- 
From: "Russell Hill" <rustyhill@earthlink.net>
To: "Harry Williams" <willisw200@msn.com>; "Dino Darling" <dino@k6rix.com>
Cc: "TowerTalk" <TowerTalk@contesting.com>
Sent: Thursday, September 06, 2007 7:36 PM
Subject: Re: [TowerTalk] Restringing Cable on Crankup Tower


>I haven't asked or tried, but is there any chance Karl Tashjian might be
> willing to supply properly sized (to order) cables professionally 
> prepared,
> for a price?
>
>
> ----- Original Message ----- 
> From: "Dino Darling" <dino@k6rix.com>
> To: "Harry Williams" <willisw200@msn.com>
> Cc: "TowerTalk" <TowerTalk@contesting.com>
> Sent: Wednesday, September 05, 2007 3:12 PM
> Subject: Re: [TowerTalk] Restringing Cable on Crankup Tower
>
>
>> If you can remove the cables, and being that you are not already
>> familiar with cable crimping, and the fact that one small mistake
>> could cause your tower to fail, I'd take the cables off and have them
>> done professionally by a local wire cable vendor.  They will have the
>> correct cable (made to roll over sheaves, usually 7x19 wire rope) and
>> the correct tools to properly crimp the ends.
>>
>> Go to...
>> http://www.mcmaster.com/
>>
>> type "1341" in the search box and read about 7X19 cable (NOT 19X7!)
>>
>> The tools and sleeves are on page "1352".
>>
>> Good Luck!
>>
>>
>> At 10:01 PM 9/5/2007, Harry Williams wrote:
>>
>>>I have a Hygain HG-70D crankup tower and have been thinking about
>>>replacing the cable. The tower is down right now and it does not
>>>appear to be a very difficult process to replace the cable. I see
>>>that the cable ends are held in place by a pair of crimped on
>>>clamps. Where can I get the clamps and what kind of tool is needed
>>>to do the crimping?
>>>
>>>73's,
>>>Harry
>>>W0LS
>>>_______________________________________________
>>>
>>>
>>>
>>>_______________________________________________
>>>TowerTalk mailing list
>>>TowerTalk@contesting.com
>>>http://lists.contesting.com/mailman/listinfo/towertalk
>>>
>>>
>>>
>>>--
>>>No virus found in this incoming message.
>>>Checked by AVG Free Edition.
>>>Version: 7.5.485 / Virus Database: 269.13.5/990 - Release Date:
>>>9/4/2007 10:36 PM
>>>
>>>
>>>
>>>
>>>--
>>>No virus found in this incoming message.
>>>Checked by AVG.
>>>Version: 7.5.485 / Virus Database: 269.13.5/990 - Release Date: 9/4/2007
>>
>> Dino - K6RIX
>> dino@k6rix.com
>>
>>
>> -- 
>> No virus found in this outgoing message.
>> Checked by AVG.
>> Version: 7.5.485 / Virus Database: 269.13.5/990 - Release Date: 9/4/2007
>>
>>
>> _______________________________________________
>>
>>
>>
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>>
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk 

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>