Towertalk
[Top] [All Lists]

Re: [TowerTalk] Inverted L Tuning Question

To: TowerTalk <towertalk@contesting.com>
Subject: Re: [TowerTalk] Inverted L Tuning Question
From: RICHARD SOLOMON <w1ksz@q.com>
Date: Fri, 5 Dec 2008 04:18:50 +0000
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
Is that article available on line ?
 
Thanks, Dick, W1KSZ> Date: Thu, 4 Dec 2008 18:22:55 -0800> From: 
n6ki73@gmail.com> To: w7why@verizon.net> CC: towertalk@contesting.com> Subject: 
Re: [TowerTalk] Inverted L Tuning Question> > The issue with teh AM BC Strong 
Signal interference is addressed in> the Nov/DEC NCJ> ( National Contest 
Journal ) magazine article> ..and article uses exact same antenna analyzer as 
Dick is using !> 73, Dennsi N6KI> > On Thu, Dec 4, 2008 at 6:09 PM, Tom Osborne 
<w7why@verizon.net> wrote:> > > Hi Dick> >> > You can get some screwy readings 
if there is a BC station nearby. I can't> > even use my analyzer here on my 160 
inverted L because of RF from the> > local.> > I have to use the SWR bridge in 
the shack. 73> > Tom W7WHy> >> >> >> > > Hi Guys,> > >> > > I'm trying to set 
up a 160-m. Inverted L for ARRL-160 this weekend but am> > > having an 
interesting tuning problem. All thoughts appreciated!> > >> > > The Inverted L 
is made up of #12 stranded copper wire 136' in total> > > length:> > >
  82' vertical and 54' horizontal. The vertical wire is spaced 6' from a> > > 
88'> > > self-supporting tower with a Cushcraft XM-240 mounted on top. (XM-240> 
> > elements> > > are not grounded) Initial radial system is 2- 135' radials 
laying on> > > the> > > ground- not much but two similar radials worked pretty 
well on my 60'> > > tower last> > > year as the towers are 150' from a salt 
water river.> > >> > > Placing the Antenna Analyzer (AIM 4170) at the base of 
the Inverted L> > gets> > > the following measurements:> > >> > > 1) With the 
coax braid connected to the tower base which has two 8'> > ground> > > rods: 
lowest SWR is 3.9 at 1.776 Mhz and Z = 79.> > >> > > 2) With coax braid only 
connected to the two radials (and not the tower> > > base): lowest SWR is 1.62 
at 1.614 Mhz and Z = 81.> > >> > > It was my understanding that the coax braid 
should be connected to both> > > the> > > radials and the base of the towers 
gnd system, but as you can see the the> > > minimum SWR
  and resonant freq. go crazy when I do.> > >> > > Any recommendations what I 
can do to get it working before tmw night?> > >> > > 73,> > > Dick- K9OM> >> > 
_______________________________________________> >> >> >> > 
_______________________________________________> > TowerTalk mailing list> > 
TowerTalk@contesting.com> > 
http://lists.contesting.com/mailman/listinfo/towertalk> >> 
_______________________________________________> > > > 
_______________________________________________> TowerTalk mailing list> 
TowerTalk@contesting.com> http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>