I think it would be a mistake to entirely cut away the gusset plates. I do
think, however, you could remove part of the plates, leaving good bracing in
the corners. I'm not sure all this would be worth the risk and trouble just
to save a few pounds. Your biggest problem will be dealing with the ongoing
growth of the tree.
------------------ Wes Attaway (N5WA) ------------------
1138 Waters Edge Circle - Shreveport, LA 71106
318-797-4972 (office) - 318-393-3289 (cell)
Computer Consulting and Forensics
-------------- EnCase Certified Examiner ---------------
-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] On Behalf Of N4NW
Sent: Monday, September 28, 2009 7:11 AM
To: wland wland; towertalk@contesting.com
Subject: Re: [TowerTalk] HF yagi - tree mount fixture - photos: Need
suggestions
I am not an engineer but I recently visited a Holiday Inn but seems
to me that removing the areas in the photo in red is going to
significantly weaken the device.
73's
Tom
At 02:15 PM 9/27/2009, you wrote:
>Hi all,
>Here is the contraption i have got a steel shop to fab.
>http://picasaweb.google.com/wlanddx/TreeMountFixture?feat=directlink
>
>Question:
> In one of the photos, i have marked cutting points in red color. Should
i
>cut or not?
> The objective is to reduce weight. Cutting the gussets will reduce the
>weight by at least
> 14lbs. Don't know about the gain in weight by cutting a section of the
>round tube for the swing gate.
>
> I plan to mount a TA-33 or A3S.
>
> I am getting ready to galvanize this contraption and will need to make a
>decision (cut or no cut?) in
> the next few days.
>
>Here are the details.
>1. Swing arm - 1/8" thick steel and weighs about 22 lbs.
>2. The rotor/bearing mount - 3/8" thick steel and weights about 84 lbs.
>3. In addition, gotta add the weight of the rotor (say 20lbs ??) + HF yagi
>(30lbs max)
>
>Since this will be up on a tree and will be secured using
>a) Multiple lag bolts (2 to 6 perhaps).
>b) There are 2 nuts welded at the top and bottom of the fixture. An EHS
>steel cable
> that is used to guy towers will be run around through a couple of 2x4
>piece of wood
> with holes drilled in it for use as spacers. Then a turnbuckle will be
>used to tighten it.
> The turnbuckle will be adjusted yearly to let the tree grow around.
>c) In addition, 2 eye bolts will be installed, one above the fixture on the
>opposite side of the
> bracket, a few feet above and below it. A safety steel cable will be
>strung through the eye bolts. This will
> act as backup in case the tree breaks off at the top or the primary
cables
>gives away.
> At any rate, i don't want this to come down. If it were to, its gotta
come
>down when the tree
> comes down. In all, there will be 4 cables around the tree to secure it.
>d) Annual inspection by a tree climber.
>e) This goes in between the branches of a tall pine at the 50ft level. At
>the
> mount point, the trunk is about 1.5 to 2 ft wide. This is a type of
>pine tree that cannot be topped.
>
>All painted with camo paint to blend in.
>
>Any comments? suggestions?
>
>73s
><name/callsign withheld to avoid detection by neighborhood busybody
>googlers>
>_______________________________________________
>
>
>
>_______________________________________________
>TowerTalk mailing list
>TowerTalk@contesting.com
>http://lists.contesting.com/mailman/listinfo/towertalk
Tom Gregory, N4NW
n4nw@n4nw.org
N4NW LLC - Complete Merchant Services
Check out local N4NW weather conditions real-time -->> http://www.n4nw.org
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|