Towertalk
[Top] [All Lists]

Re: [TowerTalk] neverseize on tower legs

To: Tek Supp <teksaport@hotmail.com>
Subject: Re: [TowerTalk] neverseize on tower legs
From: al_n6ta@comcast.net
Reply-to: "Tower and HF antenna construction topics." <towertalk@contesting.com>
Date: Wed, 13 Jan 2010 05:32:07 +0000 (UTC)
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>

So, I watched the 2x6 float to earth and decided the TowerJack was a good. 
idea  It worked well and I would recommend it.  Good for installs and take 
downs.  So, I also dropped it and it stuck like a jack knife.  Not as brite 
yellow as when new, but just as useful.  

Al 
----- Original Message ----- 
From: "Tek Supp" <teksaport@hotmail.com> 
To: towertalk@contesting.com 
Sent: Wednesday, January 6, 2010 9:46:22 PM GMT -08:00 US/Canada Pacific 
Subject: Re: [TowerTalk] neverseize on tower legs 


I second the "...but it's hard to manage aloft...".  It was not pretty nor fun 
in getting those up there and using them, but it was all I had at the time, and 
I made sure to tie off everything to a lanyard (the jack, the 2x4's and the 
jack crank arm).  Most importantly (if I may offer this adivce), watch your 
face/head when the section you are trying to get loose, does come loose.  As I 
mentioned previously, that section was being pulled from below (via ginpole), 
and when the section came loose, it shot up (and back down), and the jack and 
2x4's took a leap off the tower and ended up against me with a few bruises to 
match (luckily though they were still attached and didn't hurt anyone or 
anything below. 

  

I looked into the TowerJack and didn't buy it, but wished I had something 
easier than what I ended up doing.  So whatever you do use, tie it off and 
watch out. 

  

Thanks 

John 

K7ALA 

  


  
> Date: Wed, 6 Jan 2010 22:14:27 -0500 
> From: jimjarvis@optonline.net 
> To: towertalk@contesting.com 
> Subject: Re: [TowerTalk] neverseize on tower legs 
> 
> 
> Tony, 
> 
> Get yourself a "TowerJack". 
> 
> You'll need to overcome gravity, plus whatever alignment distortion 
> generated friction there was when you assembled, plus corrosion. 
> 
> Towerjack works. 
> 
> Car jack and 2x4's works, too, but it's hard to manage aloft. 
> 
> N2EA/Jim 
> 
> ps: it's actually easier to take this stuff apart vertically than 
> horizontally, 
> so laying it over intact and then disassembling isn't fun. Vertical 
> disassembly 
> obviously requires a ginpole. And a ground crew. 
> _______________________________________________ 
> 
> 
> 
> _______________________________________________ 
> TowerTalk mailing list 
> TowerTalk@contesting.com 
> http://lists.contesting.com/mailman/listinfo/towertalk 
                                                
_________________________________________________________________ 
Hotmail: Trusted email with Microsoft’s powerful SPAM protection. 
http://clk.atdmt.com/GBL/go/196390706/direct/01/ 
_______________________________________________ 



_______________________________________________ 
TowerTalk mailing list 
TowerTalk@contesting.com 
http://lists.contesting.com/mailman/listinfo/towertalk 
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
<Prev in Thread] Current Thread [Next in Thread>