* How about making the 'wings' bigger by bolting something to them?
Martin, HS0ZED
-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] On Behalf Of Roger (K8RI)
Sent: 08 July 2010 14:25
To: towertalk@contesting.com
Subject: Re: [TowerTalk] No Tool Fast Assembly HF Beam
On 7/8/2010 3:16 AM, Martin Sole wrote:
> I've thought about this one before and came up with the idea of using
> worm drive hose clamps. Where you have a split in the end of the
> larger tube and then using a compression worm drive hose clamp should
> work okay, many beams come with them. The problem is the need for a
> screw driver or socket that fits the hexagon head of the worm drive
> clamp but I have seen clamps, and I think you could fabricate this,
Standard nut drivers work just fine on those, but you need to remember to
mark the elements in a manner so they do not require measurement at assembly
time. That's what I like about the "tent stake" approach although it'd be
much more complicated to implement, it would be the simplest to use.
> where instead of a slotted head there was a large flat wing like
> appendage such that sufficient torque could be applied by finger and
> thumb alone to ensure a reasonable if not overly tight fix.
>
The SS hose clamps are available with this type of tightening head on the
screw, but you often need a good pair of leather gloves or pliers to tighten
them.
* How about making the 'wings' bigger by bolting something to them?
> Mark the tubes at the appropriate points and then at assembly just
> slide together until the marks line up and finger tighten the modified
> worm drive hose clamp. A similar arrangement could be done at the boom
> if the antenna is appropriately modified.
The old Cushcraft ATB-34 used a center insulator that the halves of the
driven element just stuck into and were held in place by tightening two
1/4-20 SS Round head screws with nuts on them to grip the feed line
connectors. Re the photo in the thread (what kind of antenna is this)
> Fix the boom to element clamps permanently to the boom and use wing
> nuts on the element clamps or fix a short stub at the element mount
> and then having cut the centre tube use the same process as for the
> rest of the elements. Not losing the clamps might be the biggest
> problem so you may need spares or find some way to tie them to the
elements.
>
>
Like a computer program the easier you make it to use the more difficult it
is to implement. <:-)) OTOH I think the above will work fine.
73
Roger (K8RI)
> Cheers
> Martin, HS0ZED
>
>
> -----Original Message-----
> From: towertalk-bounces@contesting.com
> [mailto:towertalk-bounces@contesting.com] On Behalf Of Roger (K8RI)
> Sent: 08 July 2010 13:45
> To: towertalk@contesting.com
> Subject: Re: [TowerTalk] No Tool Fast Assembly HF Beam
>
> On 7/7/2010 10:26 PM, gdaught6@stanford.edu wrote:
>
>> Joe wrote...
>>
>>
>>
>>> Has anyone equipped the elements of a beam with some neat quick
>>> assembly scheme? I was thinking of the buttons often found in
>>> telescopic tent poles, or the quick and easy clamps that keep the
>>> legs of my camera tripod extended.
>>>
>>>
> I'm assuming this would be a temporary "quick to set up and tear down"
> temporary set up like FD, or a camping trip.
>
> I would think the above would be a good idea. A round headed pin or
> ball with a retainer and spring loaded. IOW just like the telescopic tent
poles.
>
>> Force-12 recommends putting a pop-rivet in, but NOT popping it. Just
>> put it in and hold it in place with a turn of black electrical tape.
>> When it comes time to disassemble it, it goes really quickly!
>>
>> The element to boom connection depends on what your antenna is. I'm
>> guessing that a set of minimally tightened U-bolts would be most common.
>>
>>
> Which is what the Force 12 C-19 uses.
> 73
>
> Roger (K8RI)
>
>> 73,
>>
>> George T Daughters, K6GT
>> CU in the California QSO Party (CQP)
>> October 2-3, 2010
>>
>>
>> _______________________________________________
>>
>>
>>
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>>
>>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|