Towertalk
[Top] [All Lists]

Re: [TowerTalk] Two tools to tighten PL-259 connector shells in tight ar

To: <k3lr@k3lr.com>
Subject: Re: [TowerTalk] Two tools to tighten PL-259 connector shells in tight areas
From: "Jorge Diez - CX6VM" <cx6vm.jorge@gmail.com>
Date: Wed, 4 Jan 2012 22:27:15 -0200
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
Any video or photo to see what do you do with this tool?  I cannot
understand from the English text

Thanks!
Jorge
CX6VM

-----Mensaje original-----
De: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] En nombre de Tim Duffy K3LR
Enviado el: Miércoles, 04 de Enero de 2012 04:04 p.m.
Para: richard@karlquist.com
CC: towertalk@contesting.com
Asunto: Re: [TowerTalk] Two tools to tighten PL-259 connector shells in
tight areas

>From extensive experience in Amateur Radio applications and commercial
installations - Even connectors tightened under controlled conditions can
loosen by being outside and going through temperature variations of more
than 50 degrees) along with normal tower shaking (resonance at low wind
speeds).

The spark plug pliers (not spark plug wrench) work perfect in this
application of tightening PL-259 shells. I am not tightening a nut, so the
pliers grab enough circular area of the PL-259 shell to hold while turning
to tight - or re tight - in a tight cluster of connectors. Any more holding
power torque could damage the connector shell.

73,
Tim K3LR

-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] On Behalf Of Rick Karlquist
Sent: Wednesday, January 04, 2012 11:49 AM
To: k3lr@k3lr.com
Cc: towertalk@contesting.com
Subject: Re: [TowerTalk] Two tools to tighten PL-259 connector shells in
tight areas

Tim Duffy K3LR wrote:
> A few months ago I asked a question on this reflector about tools that
> would
> help tighten PL-259 connectors on remote coax switches, four square boxes,
> stacking boxes, etc. Anywhere there is a tightly grouped cluster of SO-239

My preferred solution is to install permanent short (~1 foot) jumpers on
hard to get to connectors on the box.  These can be installed in
consecutive order on the bench and tightened very securely under
the best conditions.  Once the box is pigtailed, then any field
tightening is being done on in-line connections and is easily done
with visegrips.

The spark plug pliers are for pulling spark plugs, not turning
them.  You still need a spark plug wrench for that.  I can't see
how spark plug pliers would be able to tighten a nut.

Rick N6RK

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
-----
Se certifico que el correo no contiene virus.
Comprobada por AVG - www.avg.es
Version: 2012.0.1901 / Base de datos de virus: 2109/4722 - Fecha de la
version: 04/01/2012

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>