Towertalk
[Top] [All Lists]

Re: [CQ-Contest] Coax Stubs for SO2R

To: "'Mike Smith VE9AA'" <ve9aa@nbnet.nb.ca>, <towertalk@contesting.com>, <cq-contest@contesting.com>
Subject: Re: [CQ-Contest] Coax Stubs for SO2R
From: "Bill Hider" <n3rr@erols.com>
Date: Tue, 8 Sep 2015 18:53:49 -0400
List-post: <cq-contest@contesting.com">mailto:cq-contest@contesting.com>
MIKE!!

Just to verify, you are putting a  1/4 wavelength 20m Shorted stub and a 1/4 
wavelength 10m Shorted stub  in parallel with the coax line at your transmitter 
while you are transmitting on 40 m, correct?

If that is correct.....
A 1/4 wave length SHORTED stub will look like an OPEN to the 20m and 10m 
harmonic of your transmitted signal and DO NOTING to the harmonic transmitted 
signal!!
That is exactly what you are seeing, is it not?
You need an 1/4 wavelength 20M OPEN stub and a 1/4 wavelength 10m OPEN  stub 
which will short out the 20m and 10m signals as they leave your transmitter.
The 10m and 20m stubs should be located several feet apart on your transmit 
line as an isolator between them.
I would try one stub at a time to be sure it performs as an open stub should  
before you combine them on the transmit coax.

Bill N3RR

-----Original Message-----
From: CQ-Contest [mailto:cq-contest-bounces@contesting.com] On Behalf Of Mike 
Smith VE9AA
Sent: Tuesday, September 08, 2015 5:14 PM
To: towertalk@contesting.com; cq-contest@contesting.com
Subject: Re: [CQ-Contest] Coax Stubs for SO2R

Thanks for the many replies so far.  So today after I got home from work I 
tried just running radio A @ about 1w on 7.000MHZ and saw S9 on 20m and s1 on 
10m.

No change switching stub in or out, so I took Jim�s(K9YC) suggestion and moved 
the stub farther away from the transceiver.  I made up 3 random length patch 
cables and so have the stub roughly either:

10-12�, 15�-17, 20�-22, 25�-27 away from the transmitter (Radio A). (rough 
guesstimates)  ( a 1/4wl, accounting for VF would be in the 23�-27� range)

No perceptible change whatsoever at any point in the line no matter where I put 
the stub.  Just the slightest SWR change when I put it in line.  Almost cannot 
detect it.

 

I am going nuts.

 

It�s either something in the shack or something outside rectifying (I guess?)  
but these are pretty low power levels. (usually 100w, but also at 1w !)

 

Radio A (transmitter in the scenario) is hooked to an amp (not turned on in 
close to a year), an antenna switch, a tuner/wattmeter (used on straightthrough 
function only, just for it�s wattmeter/SWR function.)

Radio B (receiver in this scenario) is hooked to its own power supply and coax 
straight outside to a multiband dipole some 100� from the Radio�s A�s various 
antennas. No SWR meters, switches or anything.

 

They share a 4� hole in the wall in the garage where they exit to the outside, 
where the RG8 or LMR400 coax;�s could be close to one another.

They share 120VAC  in the shack (but different power supplies)

 

I have two additional (perhaps important?) questions.  Should any of these 
harmonics between any bands sound pure and �clean�, like a real CW signal?  
Mine all sound low/muffly, wide, growly, like they have buzzing/humming AC 
riding on top of them.

 

Additionally, the AA-230pro�s manual says to make the 1/4WL stub with the end 
of the coax OPEN.  . . . .but then for the purposes of these tests, I am using 
the stubs shorted.

 

Maybe I have a ground loop somewhere and there is feedback or an isolation 
problem on the shacks�s 120VAC line?

 

Mike

_______________________________________________
CQ-Contest mailing list
CQ-Contest@contesting.com
http://lists.contesting.com/mailman/listinfo/cq-contest


-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2015.0.6125 / Virus Database: 4409/10599 - Release Date: 09/08/15

_______________________________________________
CQ-Contest mailing list
CQ-Contest@contesting.com
http://lists.contesting.com/mailman/listinfo/cq-contest
<Prev in Thread] Current Thread [Next in Thread>