My WT-51 also has the welded tabs to support the rotor plate.
Don W7WLL
-----Original Message-----
From: KJ6Y--- via TowerTalk
Sent: Sunday, September 17, 2017 2:45 PM
To: towertalk@contesting.com
Subject: [TowerTalk] Fwd: FW: Installing a Ham-IV rotor on Tashjian w-51
tower
I just had a chance to look at he W-51 I have for sale. 35 inches down
from the top are tabs welded inside each leg to support the rotator plate.
I'm not sure it Tashjian stills does it this way but every Tri-Ex W-51 I've
ever installed or worked on (and there were many), all had the tabs.
Skip, KJ6Y
Communications Service Co
818-522-5421 cell
_www.kj6y.com_ (http://www.kj6y.com/)
In a message dated 9/17/2017 12:50:49 P.M. Pacific Daylight Time,
maflukey@gmail.com writes:
Hi Bob,
I have a W51 vintage 1967. On this tower there are no rotor plate tabs on
the legs. The rotor plate is drilled in each corner and uses (3) wedge
lock arrangements. Each wedge lock was fabricated by welding a piece of
threaded rod to a short section of structural angle. The threaded rod is
mounted through the hole in the rotor plates while the angle straddles the
inside of the tower leg. When a nut is drawn up on the threaded rod, it
wedges the angle tight against the inside of the tower leg.
Hope this info helps.
P.S. I would avoid drilling though the legs - it will create stress
concentrations and weaken the structure.
73
Matt
KM5VI
-----Original Message-----
From: TowerTalk [mailto:towertalk-bounces@contesting.com] On Behalf Of Bob
Richards
Sent: Saturday, September 16, 2017 2:42 PM
To: KJ6Y@aol.com; towertalk@contesting.com
Subject: Re: [TowerTalk] Installing a Ham-IV rotor on Tashjian w-51 tower
I went all over the inside of the top tower section and found no tabs. My
idea is to drill, tap, and put in short bolts where the tabs should be,
sitting the rotator plate on the bolt heads. I do plan to contact Tashjian
on Monday before doing this. Nice to know an experienced W-51 installer
had
to bend the bracing to install the rotator. Perhaps I missed it but I've
seen nothing in any of the tower documentation that describes rotator
installation.
I do expect to be pleased with my tower once I get the rotator installed.
Many thanks to everyone for all the feedback to my questions.
Bob NZ6G
On 9/15/2017 8:16 PM, KJ6Y@aol.com wrote:
On the W-51, the rotator plate sits about 3 ft down from the top on
tabs welded inside the tower. You have to bend the diagonal bracing
slightly to get the rotator in and then bend them back. There should
be no reason to mount the rotator down 7 ft.
I've done many W-51 installations and service and it's a fine tower.
Skip, KJ6Y
Communications Service Co
818-522-5421 cell
www.kj6y.com <http://www.kj6y.com/>
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
---
This email has been checked for viruses by AVG.
http://www.avg.com
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
Skip, KJ6Y
Communications Service Co
818-522-5421 cell
_www.kj6y.com_ (http://www.kj6y.com/)
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
---
This email has been checked for viruses by AVG.
http://www.avg.com
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|