Towertalk
[Top] [All Lists]

Re: [TowerTalk] Al-to-Al

To: <towertalk@contesting.com>
Subject: Re: [TowerTalk] Al-to-Al
From: "Keith Dutson" <kdutson@sbcglobal.net>
Date: Wed, 14 Feb 2018 19:16:16 -0600
List-post: <mailto:towertalk@contesting.com>
Noalox is good stuff.  I recently disassembled a Force 12 C-3S that was put in 
service many years ago.  Only one joint had to be heated with a propane torch 
to get it freed.  The other joints came apart using only two hands.

73, Keith NM5G

-----Original Message-----
From: TowerTalk [mailto:towertalk-bounces@contesting.com] On Behalf Of Bill M
Sent: Wednesday, February 14, 2018 3:09 PM
To: towertalk@contesting.com
Subject: Re: [TowerTalk] Al-to-Al

We’ve tried pretty much everything in our salt air environment of South 
Florida. Most here use Noalux successfully over the past 30+ years. 
Bill W2CQ


> On Feb 14, 2018, at 3:13 PM, Tom_N2SR via TowerTalk 
> <towertalk@contesting.com> wrote:
> 
> I use an acid brush that I cut the bristles down to about 1/4"   
> Apply it, then use the brush to pull as much off as you can.  The bristles 
> make "groves" like thinset (when you tile a floor).   
> YMMV.
> Tom, N2SR
> 
> 
>      From: Steve Bookout <steve@nr4m.com>
> To: towertalk@contesting.com
> Sent: Tuesday, February 13, 2018 8:39 PM
> Subject: Re: [TowerTalk] Al-to-Al
> 
> I must agree with Tim on this.  This stuff has never let me down.
> To make a bit easier to apply, and although it may be a 'sin', I apply 
> it to the inner element, then spray WD-40 on it and spread it with 
> vinyl gloved hand.
> Goes on a bit more even this way.
> 
> 73 de Steve, NR4M
> 
>> On 2/13/2018 7:56:PM, Tim Duffy wrote:
>> I used Penetrox for years - noticed that after 10 years or more that 
>> the Penetrox would dry out and turn to a crusty dust. I mentioned 
>> that to W3LPL.H Frank said try Jet Lube SS-30 - which is what he uses 
>> at his mega station for all of his antennas.
>> 
>> I have been sold on Jet Lube SS-30 ever since. After 25 years here at 
>> K3LR - the Jet Lube SS-30 comes apart and is clean and offers a great 
>> low loss connection. I use it everywhere hardware and connections are 
>> involved (even in the shack) - as does W3LPL. Do not worry that this 
>> is copper based paste
>> - it works SUPER for Al to Al.
>> 
>> https://www.dxengineering.com/parts/jtl-12555
>> 
>> 73
>> Tim K3LR
>> 
>> -----Original Message-----
>> From: TowerTalk [mailto:towertalk-bounces@contesting.com] On Behalf 
>> Of Bob K6UJ
>> Sent: Tuesday, February 13, 2018 6:45 PM
>> To: Kim Elmore; towertalk@contesting.com
>> Subject: Re: [TowerTalk] Al-to-Al
>> 
>> Kim,
>> You will get several suggestions on this.  I use Penetrox.  Used it 
>> on aluminum antenna element joints for years.  Does a great job of 
>> preventing corrosion and preserving the aluminum.  I have taken apart 
>> yagis that have been up for over 20 years and the exterior of the 
>> aluminum tubes were corroded, naturally, but the internal mating 
>> surfaces where the penetrox was used were shiny and bright, like new.  
>> I first started using it years ago on KLM antennas, they provided a 
>> tube with their antennas, and still use it.DX engineering has it 
>> :https://www.dxengineering.com/parts/dxe-p8a
>> 
>> 
>> BobK6UJ
>> 
>> 
>> 
>>         From: Kim Elmore <cw_de_n5op@sbcglobal.net>
>>   To: towertalk@contesting.com
>>   Sent: Tuesday, February 13, 2018 2:09 PM
>>   Subject: [TowerTalk] Al-to-Al
>>     
>> When assembling Al -to-Al junctions in an Antenna, what 
>> anti-corrosion compound should be used at the joints?
>> 
>> Kim N5OP
>> 
>> "People that make music together cannot be enemies, at least as long 
>> as the music lasts." -- Paul Hindemith 
>> _______________________________________________
>> 
>> 
>> 
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>> 
>> 
>>     
>> _______________________________________________
>> 
>> 
>> 
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>> 
>> _______________________________________________
>> 
>> 
>> 
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>> 
> 
> _______________________________________________
> 
> 
> 
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
> 
> 
> 
> _______________________________________________
> 
> 
> 
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
<Prev in Thread] Current Thread [Next in Thread>