VHFcontesting
[Top] [All Lists]

Re: [VHFcontesting] MORE more odds and ends F.S.

To: 'Pack Rats Reflector' <packrats@mailman.qth.net>, VHF Contest Reflector <vhfcontesting@contesting.com>
Subject: Re: [VHFcontesting] MORE more odds and ends F.S.
From: Bill Olson <callbill@hotmail.com>
Date: Wed, 6 Dec 2017 22:16:14 +0000
List-post: <mailto:vhfcontesting@contesting.com>
The CX531N is brand new..


bill


________________________________
From: Bill Olson <callbill@hotmail.com>
Sent: Wednesday, December 6, 2017 10:14 PM
To: 'Pack Rats Reflector'; VHF Contest Reflector
Subject: MORE more odds and ends F.S.


CX531N coax relay 12v, common port type N. N.O. and N.C. ports hard wired for 
RG58 or RG142 size coax.. will handle a couple 100 watts up to 432. heck,.. 
here's a data sheet: 
https://www.thedxshop.com/tohtso-cx-531n-coaxial-relay.html   $15 plus ship PP 
preferred..


bill K1DY




________________________________
From: Bill Olson <callbill@hotmail.com>
Sent: Wednesday, December 6, 2017 9:51 PM
To: 'Pack Rats Reflector'; VHF Contest Reflector
Subject: more odds and ends F.S.


all the past stuff is sold, including the beam, but I keep finding more..


Tohtsu CX-600M coax relay.. in *like new* condition (that means it was in the 
rover station switching a few watts  only a couple times a year).. 12v, with 
(yeah I know) UHF connectors.. but at 6 or 2M who cares and this relay will 
handle a kilowatt with 50-60dB isolation.. data here: 
https://www.rfparts.com/cx600m.html  $25 plus ship.. PP preferred..



bill, K1DY


________________________________
From: packrats-bounces@mailman.qth.net <packrats-bounces@mailman.qth.net> on 
behalf of Bill Olson <callbill@hotmail.com>
Sent: Friday, December 1, 2017 7:18 PM
To: 'Pack Rats Reflector'; VHF Contest Reflector
Subject: [Packrats] odds and ends F.S.


Hi all, I'm still cleaning up in the shack. Here's some odds and ends for sale:


150 watt 903MHZ linear power amp. This was put together by N2CEI and belonged 
to W0RSJ. It's based on the Motorola pallet shown in the picture in the link 
below. It's built into a Hammond Die cast box with an adequate chunk of 
heatsink. The bias board is built in and has a GND to TX PTT circuit. Type N 
connector in and out. needs a few watts to drive to full out. Requires 24volts 
DC and that's pretty much it.. pix available..

http://www.qsl.net/n9zia/stf2520a/vhfsouth/150-ohview.jpg<https://nam02.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.qsl.net%2Fn9zia%2Fstf2520a%2Fvhfsouth%2F150-ohview.jpg&data=02%7C01%7Ccallbill%40hotmail.com%7C9336b48e6d084b18d47f08d538f051aa%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477527168134338&sdata=QSe309Bcv8fBnATsNghtpkeySM5x%2BqR8mziSkhCMuro%3D&reserved=0>
   $75 OBO


power dividers are built in 1" square aluminum tube w/N female connectors. used 
and working could use some cleaning up..

1296 2 way power divider $15

432 2 way power divider $15


I still have the K1FO 25 element Yagi.. refurbished and tested.. it would be 
local pickup preferrably though I would meet someone in northern New England 
just for the gas $$. This could be shipped, I'm not hot to pack it up, but will 
discuss.. This is a $280 antenna new! I'd really like to get it to someone 
before the January contest! $60


Tohtsu CX600NC coax relay.. brand new, 12v coil, Type N common port, hard-wire 
RG8 for N.C. and N.O. ports..  will handle a kilowatt at VHF. here's the date 
sheet: 
http://vhelectronics.sk/index.php/en/koaxial_relay/cx-600nc-detail<https://nam02.safelinks.protection.outlook.com/?url=http%3A%2F%2Fvhelectronics.sk%2Findex.php%2Fen%2Fkoaxial_relay%2Fcx-600nc-detail&data=02%7C01%7Ccallbill%40hotmail.com%7C9336b48e6d084b18d47f08d538f051aa%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636477527168134338&sdata=Qt3MOF4txR40u5jQRZIV1d5u0OQSMcf44p74qkdL4dk%3D&reserved=0>
  $20


shipping extra on all


bill, K1DY in central Maine





_______________________________________________
VHFcontesting mailing list
VHFcontesting@contesting.com
http://lists.contesting.com/mailman/listinfo/vhfcontesting

<Prev in Thread] Current Thread [Next in Thread>