WriteLog
[Top] [All Lists]

Re: [WriteLog] WAE Can't send QTCs to other continents

To: "REFLECTOR writelog" <writelog@contesting.com>,"Jim Smith" <jimsmith@shaw.ca>
Subject: Re: [WriteLog] WAE Can't send QTCs to other continents
From: "???sta?t???? SV1DPI" <kstama@tee.gr>
Date: Mon, 10 Nov 2003 11:43:05 +0200
List-post: <mailto:writelog@contesting.com>
Hello
I had the same problem
I was using a pk900 for transmit and i had the same problem to send qtc.
I tried many times and only 1 or 2 times i had limited success.
Same behaviour exactly.
I was using the mark v with writelog 10.42c and a pk900 tnc for transmit and
pk900 - mmtty for receive
Kostas Stamatis, SV1DPI
Electrical Engineer
PO Box 66 - 30100 Agrinio
Greece

----- Original Message -----
From: "Jim Smith" <jimsmith@shaw.ca>
To: <writelog@contesting.com>
Sent: Sunday, November 09, 2003 10:01 AM
Subject: Re: [WriteLog] WAE Can't send QTCs to other continents


> Nothing like posting to the reflector and finding the trouble oneself
> immediately after.  However, the solution is as puzzling as the problem.
>
> I looked at the volume conrol settings and noted that the Wave level
> control was zeroed.  Moved the slider up a bit and now QTCs get
> transmitted.  Well, one would expect the Wave level control to affect
> this but one would also expect it to affect everything else.  So how was
> I able to get any tones out of the soundcard at all with the Wave level
> control zeroed?  Changing the Wave level affected only QTC tone levels,
> not QRV or QSL button levels.
>
> Another puzzlement is that I thought the sound card settings were
> adjusted by WL so wouldn't expect the Wave level to be zeroed.
>
> BTW I'm using K6STI's RITTY.
>
> All's well that ends well so I'll be a happy camper when WAE activity
> comes back tomorrow am.
>
> 73 de Jim Smith    VE7FO
>
> Jim Smith wrote:
>
> > I have been unable to send QTCs in the WAE test.  I can receive them
> > just fine.  If I hit ALT-S the Send QTC dialogue box comes up showing
> > the 10 QTCs that will be sent. If I click on the QRV button it does
> > what it is supposed to do.  Ditto for the QSL button.  When I hit the
> > Send QTC button the rig goes into transmit mode and the QTCs get
> > written to the window where all the stuff I send and receive is
> > displayed. However, they don't get transmitted, the Power Out meter
> > shows zero and there is no sound from the MkV Monitor.  I plugged an
> > amplified spkr into the soundcard Line Out and the QRV/QSL buttons
> > generate tones but the Send QTC button doesn't.  There is a valid,
> > off-the-continent call in the Call window.
> >
> > This is my 2nd and maybe my 3rd RTTY WAE.  Never had this trouble
> > before.  I've used the same version of WL in all 3 WAE tests - 10.27G.
> >
> > Any ideas anyone?
> >
> > 73 de Jim Smith    VE7FO
> >
> > _______________________________________________
> > WriteLog mailing list
> > WriteLog@contesting.com
> > http://lists.contesting.com/mailman/listinfo/writelog
> > WriteLog on the web:  http://www.writelog.com/
> >
>
>
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web:  http://www.writelog.com/


_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web:  http://www.writelog.com/

<Prev in Thread] Current Thread [Next in Thread>