This was true with ISA but is not the case with PCI cards...
I have 4 COM ports (in addition to the usual COM1 and COM2) sharing IRQ 18.
All are working tickety-boo.
I don't what the problem is Alan... But it might not be the COM port... It
seems surprising that more than one piece of hardware is at fault. Have you
carefully considered all other possibilities? Perhaps a bad cable... Using a
crossover cable by mistake for example, can be hard to catch since they all
look the same... ( I've done that ;-)
You can download a program called commander from http://www.qsl.net/dxlab/
which is VERY helpful debugging radio communication problems.
> -----Original Message-----
> From: writelog-bounces@contesting.com
> [mailto:writelog-bounces@contesting.com] On Behalf Of Jim Dunbar
> Sent: August 28, 2004 16:17
> To: 'Alan J.Donziger'; writelog@contesting.com
> Subject: RE: [WriteLog] Comm Port Problem update
>
>
> Hello,
>
> The computer operating system will allow certain devices to
> share the same interrupts when the computer has many devices.
> However, the devices using the same interrupts cannot be
> using them at the same time. So, it may be worthwhile trying
> to get separate interrupt assignments for these devices, if possible.
>
> Thanks,
>
>
> Jim Dunbar
> Senior Electrical Engineer
> Advanced Programs Division
> AeroSpace Integration Corporation
> Crestview, Florida
> 850-689-2978 (Office)
> 850-384-8171 (Mobile)
> 850-983-8155 (Home)
>
> -----Original Message-----
> From: writelog-bounces@contesting.com
> [mailto:writelog-bounces@contesting.com] On Behalf Of Alan J.Donziger
> Sent: Saturday, August 28, 2004 12:44 PM
> To: writelog@contesting.com
> Subject: [WriteLog] Comm Port Problem update
>
> First - thanks to all who replied to my earlier post. I tried
> the solutions proposed that I hadn't tried before. Still no
> luck. I came across a PCI card with 2 comm ports and one lpt
> port at Comp USA. I installed that and same result.
>
> The two COMM ports show up in device manager as COMM 3 and
> COMM 6 and show
> as operating properly. COMM 1 will power either radio with
> no problem. WL
> is seiing COMM 3 and 6 as when I select them no port not
> available message. But they dont seem to communicate with radios.
>
> BTW: COMM 3 and 6 do work with a serial mouse.
>
> There is one thing I do notice that I think may be the
> problem. The new device show up as using IRQ 16. Two other
> devices are also on IRQ 16 -USB controller and graphics
> controller. I dont know if that is the problem. However I
> cant find any way to change the IRQ of new card. Device
> manager is not giving me the option of changing it.
> Is this an IRQ problem and if so is there a fix?
>
> Thanks
> Alan/N3AD
>
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web: http://www.writelog.com/
>
>
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web: http://www.writelog.com/
>
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|