I may not be able to help you with #1 because I use the DXTelnet interface with
WriteLog. Open the Packet Spots window and see if you are getting spots in the
Packet Spots window.
#2. To get callsigns to highlight in Rttyrite, make sure you set the Super
Check Partial file. For instructions on how to do that. Go to the Tutorials
Page on rttycontesting.com and click on the link "Setting the DTA file for
Super Check Partial" or go directly via the link here:
http://rttycontesting.com/writelog/supercheckpartial/supercheckpartial_page1.htm
In one of the Rttyrite menus, you have the option to highlight callsigns after
a DE is received or not. I use this feature because it allows callsigns that
are not in the Super Check Partial file to highlight as well as those that are
in the file.
#3. Use a %E at the end of all RTTY messages to end the transmission. Also you
should include at least one space at the end of all your message before putting
the %E. If you don't put a space or two, noise characters will be appended to
the end of your message. DON'T FORGET THE SPACE!
#4. I don't completely understand this question, but sample messages can be
found on rttycontesting.com from the home page by clicking the link in the link
bar named "RTTY Contest Messages". Use the pull down menu on the RTTY Contest
Message page to select the contest you want. I need to update these pages, but
you will get the idea of what you need to do. If not, send me a personal note
and I'd be happy to help.
#5. WL has special functions for operating the K3 for SO2V. Ed Muns (w0yk at
msn.com)probably is best to address this one. Maybe if I could get Elecraft to
send me a K3 with a second sub-receiver, I'd be happy to document how to set up
WriteLog for it. But I don't think I'll be that lucky. Maybe one day I'll be
able to afford one.
73, Don AA5AU
>________________________________
> From: Ken Chandler <g0orh@sky.com>
>To: writelog@contesting.com
>Sent: Wednesday, January 25, 2012 8:30 AM
>Subject: [WriteLog] WriteLog BARTG RTTY test
>
>Hi ALL
>Need a bit of advice and help in getting WL 11.1, going.
>Purchased WL some time ago and Just got round to setting it up for the BARTG
>RTTY contest, Have migrated from WT!!
>I'm running a K3, MicroHam keyer2,
>
>
>Can someone shed some light on a few issues I have below!!!
>
>1, I'm logged in to telnet ve7cc.net RBN but no spots are being populated in
>the band map!!
>
>2, WL and RTTY is working fine in FSK, however is there a feature to auto
>highlight by color an incoming RTTY callsign, and mult by different color!!
>
>3, I cannot seem to get rtty to stop diddling after a message is sent, what
>command is used at the end of cq TEST to stop the transmission!!
>Further, I cannot find a list of character commands for the CW RTTY set-up
>edit window!!
>
>4, Thought I read that all contests are pre set for send rx traffic info,
>this doesn't appear to be the case as It does not send the serial exchange
>hence my query above.
>
>5, one reason I bought WL was its ability to operate SO2V with my K3, this I
>will sort out later, however is there a feature whereby I can set the band
>map for s&p via the 2nd VFO!!
>
>
>Thanks
>
>Regards
>
>Ken..G0ORH / M3i
>
>
>
>
>_______________________________________________
>WriteLog mailing list
>WriteLog@contesting.com
>http://lists.contesting.com/mailman/listinfo/writelog
>WriteLog on the web: http://www.writelog.com/
>
>
>
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|