Yaesu
[Top] [All Lists]

[Yaesu] FT1000D gone deaf

To: <yaesu@contesting.com>
Subject: [Yaesu] FT1000D gone deaf
From: tgstewart@pepco.com (tgstewart@pepco.com)
Date: Mon, 20 Aug 2001 08:08:17 -0400
This is a multipart message in MIME format.
--=_alternative 00427F4F85256AAE_=
Content-Type: text/plain; charset="us-ascii"

Chances are it's the first coil to ground in the bandpass filter...if it's 
the bandpass filter.  Does sensitivity come back at the next range higher?
I dont remember if the older 1000 (vs MP) has input LP/HP filtering at 
all, but the same coil tends to go bad in those as well.

I never had a problem with my D, but I've replaced several of these little 
coils in my MP's.  I've not had any fail since I put RX limiters on them.

I've never had any problems other than those first coils to ground in the 
filter sections.

73, Ty K3MM





Robin Thompson <robin@g3tkf.freeserve.co.uk>
Sent by: yaesu-admin@contesting.com
08/19/2001 12:39 PM

 
        To:     yaesu@contesting.com
        cc: 
        Subject:        [Yaesu] FT1000D gone deaf


Hi all
I recently discovered my FT1000D has gone low gain above 12Mhz - by
around 12dBs or so. Probably the results of being a mult rig during a
recent contest ! It is fine (by comparing with another FT1K) up to that
frequency. Presumably a component in the bandpass switching has gone -
any ideas which may be the culprit ?
G3TKF
Robin Thompson
_______________________________________________
Yaesu mailing list
Yaesu@contesting.com
http://lists.contesting.com/mailman/listinfo/yaesu



--=_alternative 00427F4F85256AAE_=
Content-Type: text/html; charset="us-ascii"


<br><font size=2 face="sans-serif">Chances are it's the first coil to ground in 
the bandpass filter...if it's the bandpass filter. &nbsp;Does sensitivity come 
back at the next range higher?</font>
<br><font size=2 face="sans-serif">I dont remember if the older 1000 (vs MP) 
has input LP/HP filtering at all, but the same coil tends to go bad in those as 
well.</font>
<br>
<br><font size=2 face="sans-serif">I never had a problem with my D, but I've 
replaced several of these little coils in my MP's. &nbsp;I've not had any fail 
since I put RX limiters on them.</font>
<br>
<br><font size=2 face="sans-serif">I've never had any problems other than those 
first coils to ground in the filter sections.</font>
<br>
<br><font size=2 face="sans-serif">73, Ty K3MM</font>
<br>
<br>
<br>
<br>
<table width=100%>
<tr valign=top>
<td>
<td><font size=1 face="sans-serif"><b>Robin Thompson 
&lt;robin@g3tkf.freeserve.co.uk&gt;</b></font>
<br><font size=1 face="sans-serif">Sent by: yaesu-admin@contesting.com</font>
<p><font size=1 face="sans-serif">08/19/2001 12:39 PM</font>
<br>
<td><font size=1 face="Arial">&nbsp; &nbsp; &nbsp; &nbsp; </font>
<br><font size=1 face="sans-serif">&nbsp; &nbsp; &nbsp; &nbsp; To: &nbsp; 
&nbsp; &nbsp; &nbsp;yaesu@contesting.com</font>
<br><font size=1 face="sans-serif">&nbsp; &nbsp; &nbsp; &nbsp; cc: &nbsp; 
&nbsp; &nbsp; &nbsp;</font>
<br><font size=1 face="sans-serif">&nbsp; &nbsp; &nbsp; &nbsp; Subject: &nbsp; 
&nbsp; &nbsp; &nbsp;[Yaesu] FT1000D gone deaf</font></table>
<br>
<br>
<br><font size=2 face="Courier New">Hi all<br>
I recently discovered my FT1000D has gone low gain above 12Mhz - by<br>
around 12dBs or so. Probably the results of being a mult rig during a<br>
recent contest ! It is fine (by comparing with another FT1K) up to that<br>
frequency. Presumably a component in the bandpass switching has gone -<br>
any ideas which may be the culprit ?<br>
G3TKF<br>
Robin Thompson<br>
_______________________________________________<br>
Yaesu mailing list<br>
Yaesu@contesting.com<br>
http://lists.contesting.com/mailman/listinfo/yaesu<br>
</font>
<br>
<br>
--=_alternative 00427F4F85256AAE_=--

<Prev in Thread] Current Thread [Next in Thread>