NY9Y -Mike,
Sounds like a neat program, thanks for link... however with all due
respect...I'm thinking the "feedline" is not being referenced. It is the
"transmission feedline" the coax that connects the amp to the
transceiver/transmitter, not the coax that runs to the antenna.
Theory is solid, yet real time first hand experiences speak loudly. When
users experience controlled SWR by means of "transmission feedline" lengths,
it's is hard to convince otherwise.
I would think though as has been mentioned there is a dynamic that exists,
by means of use of various transceiver/amplifier's. So what one finds
acceptable, may not work the same for others.
I do know that in my past history, there is textbook theory, then there is
the way I am forced to implement such at times, and darn would ya know it
still works, for the most part.
I expect the end results all vary based on the variable factors that
contribute to the results!...Resulting in all the various different
experiences posted.
Regards,
Ross KB8NTY
http://www.rossradio.net/
https://groups.yahoo.com/neo/groups/groundradial/conversations/messages
***************************************************************************************
----- Original Message -----
From: "MICHAEL HUGHES" <mhughes149@hotmail.com>
To: "Jim W7RY" <w7ry@centurytel.net>; "KB8NTY" <kb8nty@wowway.com>;
<amps@contesting.com>
Sent: Saturday, January 10, 2015 9:13 PM
Subject: RE: [Amps] Alpha Input SWR
There is a web site "RFDUDE.com". There is a free, easy to use Smith Chart
Program there.
Changing the length of the transmission line merely moves the complex
impedance around the VSWR circle. Start with a complex impedance of say,
30 -j20. Then insert a piece of transmission line. You can change the
length of the transmission line by using the up and down arrows on your
keyboard. The impedance does change but it is still on the VSWR circle and
is not normalized to 50 ohms.
I think someone mentioned this when this question first surfaced.
Handy little program.
Mike NY9Y
From: w7ry@centurytel.net
To: kb8nty@wowway.com; amps@contesting.com
Date: Sat, 10 Jan 2015 17:06:26 -0800
Subject: Re: [Amps] Alpha Input SWR
I have found that I use a 6' cable between SB220s and rigs for best SWR.
I also tune the input coils using this length and advise my customers to
do
the same when they use their amps.
73
Jim W7RY
-----Original Message-----
From: KB8NTY
Sent: Saturday, January 10, 2015 1:01 PM
To: amps@contesting.com
Subject: Re: [Amps] Alpha Input SWR
My Amp Supply LK-500ZB GG. amp manual also states to use a 6' length coax
between your exciter's RF output and the LK-500ZB RF input connector.
Possibly the feeder length does factor in!
-73-
Ross KB8NTY
http://www.rossradio.net/
https://groups.yahoo.com/neo/groups/groundradial/conversations/messages
***************************************************************
"Collins Radio recommends a 20.5 ft. coax between exciter and linear amp.
.Perhaps this would work with the Alpha.
73, Jim - w5ifp@gvtc.com"
-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2015.0.5577 / Virus Database: 4257/8901 - Release Date: 01/10/15
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2015.0.5577 / Virus Database: 4257/8901 - Release Date: 01/10/15
-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2015.0.5577 / Virus Database: 4257/8901 - Release Date: 01/10/15
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|