There is no reason to get defensive about your program, I did not
mention any specific program by name. The N4PY program is known to
be excellent plus add some excellent capability to the Orion. Most
everyone who uses it say's they really like it. However one could
argue that I can move up 5kc with my Orion just as quick as you can
reach over, grab your mouse, move the cursor to the correct screen
location, and then click a mouse. My personal choice is to not to
use a control program, and not because anything may be wrong with
it, simply because I prefer 'hands on' operation...just old
fashioned maybe? But it still works for me in DX'ing and especially
in contesting.
Tom - W4BQF
----- Original Message -----
From: "Carl Moreschi" <n4py@earthlink.net>
To: "tentec" <tentec@contesting.com>
Sent: Monday, January 24, 2005 4:52 PM
Subject: [TenTec] Advantages of computer control for s DX'er
Tommy,
I consider myself a serious DX'er and would not think of operating
any of my
radios without my control program. I can find the caller in a
split DX
pileup much faster with the aid of my control program. I also can
band hop
around to check out several different frequencies much quicker,
with all my
settings saved at each frequency. When a DX station is listening
on his own
frequency and suddenly announces he is listening up 5, I can be
there in a
second and beat everyone else calling there.
Carl Moreschi N4PY
Franklinton, NC
----- Original Message -----
From: "Tommy" <>
To: <tentec@contesting.com>
Sent: Monday, January 24, 2005 4:44 PM
Subject: Re: [TenTec] Orion Warranty
The bottom line is a control program should be an 'addition to' a
radio, but not 'in place of' parts of a radio. I think a lot of
us
much rather utilize the radio rather than play with a computer. I
doubt that a serious DX'er or contester uses control programs for
their operations, therefore, again, the radio should work
stand-alone.
Tom - W4BQF
----- Original Message -----
From: "Toby Pennington" <toby423@earthlink.net>
To: <tentec@contesting.com>
Sent: Monday, January 24, 2005 2:55 PM
Subject: Re: [TenTec] Orion Warranty
> Interesting about the RIT encoder.
> Someone suggested using the N4py control program and leaving
> the
> knobs alone
> on the front panel, that way they will last longer and the
> front
> panel will
> not show wear. However, I know that is not the answer to your
> problem, and
> the encoders should be holding up better. Toby W4CAK
>
>
> ----- Original Message -----
> From: "melinda lyon" <melindalyon@juno.com>
> To: <tentec@contesting.com>
> Sent: Monday, January 24, 2005 7:55 AM
> Subject: [TenTec] Orion Warranty
>
>
>>
>>
>> RIT/XIT Encoder
>>
>> Well I am now on my third RIT/XIT encoder. It is discouraging
>> that TEN
>> TEC does not think this is a problem. I have talked to them
>> (Paul
>> Clinton
>> at Ten Tec) about it, and they will replace it no problem, but
>> fixing the
>> design so it is not a problem again and again, no they are not
>> at
>> that
>> point yet. And yes pulling out on the knob works for a awhile,
>> but after
>> a period of time the encoders go intermittent again.
>>
>> Robye Lahlum
>>
>> W1MK
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|