Topband
[Top] [All Lists]

Re: Topband: Easy Inverted L for 169 (NCJ M/A 2011) Info Needed

To: "Michael Goins" <wmgoins@gmail.com>
Subject: Re: Topband: Easy Inverted L for 169 (NCJ M/A 2011) Info Needed
From: "ZR" <zr@jeremy.mv.com>
Date: Wed, 9 Nov 2011 16:04:01 -0500
List-post: <topband@contesting.com">mailto:topband@contesting.com>
I run mine at 12' so I can get a truck up the path to the back acreage.

Carl
KM1H

  ----- Original Message ----- 
  From: Michael Goins 
  To: ZR 
  Cc: W0MU Mike Fatchett ; topband@contesting.com 
  Sent: Wednesday, November 09, 2011 1:48 PM
  Subject: Re: Topband: Easy Inverted L for 169 (NCJ M/A 2011) Info Needed


  How high off the ground does the feed point need to be on 160 to be 
considered elevated enough to use tuned radials? I have the space  - nine acres 
- but deer are an issue with radials.

  Mike, k5wmg




  On Wednesday, November 9, 2011, ZR <zr@jeremy.mv.com> wrote:
  > Installing a dense radial field in the first 50' is the most important step
  > for a small lot. Galvanized and plastic dipped rabbit fence works wonders
  > for that. Solder wires to the ends to extend the radial field however you
  > can.
  >
  > Carl
  > KM1H
  >
  >
  > ----- Original Message -----
  > From: "W0MU Mike Fatchett" <w0mu@w0mu.com>
  > To: <topband@contesting.com>
  > Sent: Tuesday, November 08, 2011 1:57 PM
  > Subject: Re: Topband: Easy Inverted L for 169 (NCJ M/A 2011) Info Needed
  >
  >
  >> If the feedpoint is elevated you should have 4 tuned radials.  If it is
  >> ground mounted it needs radial field just like a vertical.  32 is a
  >> decent number more is better of course.  They don't have to be 1/4
  >> either to work.
  >>
  >> The current balun or choke is best at the feedpoint but some will also
  >> put one at the radio.
  >>
  >> Mike W0MU
  >>
  >> J6M CQ WW DX CW Contest 2011
  >> J6/W0MU November 21 - December 1 2011
  >> W0MU-1 CC Cluster w0mu.net
  >>
  >>
  >> On 11/7/2011 9:30 AM, Mark Adams wrote:
  >>> Hi Gang,
  >>>
  >>> I am planning to try this antenna for the winter and need more
  >>> information.
  >>> The author, NE0U, seems to have no known email address that I can find so
  >>> here goes.
  >>>
  >>>     1. I assume that the vertical radiator and the ground radial are both
  >>>     the SAME length. Correct?
  >>>     2. The sketch on page 20 shows the Ferrite Current Balun a the
  >>>     feedpoint, but the text of the article has it at the transmitter.
  >>> Which is
  >>>     correct? Does it matter?
  >>>
  >>> Yes, I could goof around with these two items, but I'd rather just put it
  >>> up and dink around only if necessary.
  >>>
  >>> Thanks es 73,
  >>> Mark K2QO
  >>> K2 #543
  >>> FN03ra
  >>> _______________________________________________
  >>> UR RST IS ... ... ..9 QSB QSB - hw? BK
  >> _______________________________________________
  >> UR RST IS ... ... ..9 QSB QSB - hw? BK
  >>
  >>
  >> -----
  >> No virus found in this message.
  >> Checked by AVG - www.avg.com
  >> Version: 10.0.1411 / Virus Database: 2092/4005 - Release Date: 11/08/11
  >>
  >
  > _______________________________________________
  > UR RST IS ... ... ..9 QSB QSB - hw? BK
  >

  -- 
  Michael Goins
  Professor, Writing
  University of Texas at San Antonio

  Michael Goins
  2508 Timbercreek Road
  Pipe Creek, Texas 78063

  Michael Goins, Owner/Editor
  Natural Awakenings-San Antonio/Hill Country magazine
  Currently distributing 20,000+ magazines in 450+ locations here with an 
online edition that gets emailed across the globe!


  Mike
  "The writer hides his crazy. It's like a little secret present inside filled 
with bees." - Chuck Wendig


  Mike
  "Writing is art. Editing is science. All of it together is craft." - Chuck 
Wendig








------------------------------------------------------------------------------

  No virus found in this message.
  Checked by AVG - www.avg.com
  Version: 10.0.1411 / Virus Database: 2092/4006 - Release Date: 11/09/11
_______________________________________________
UR RST IS ... ... ..9 QSB QSB - hw? BK

<Prev in Thread] Current Thread [Next in Thread>