A thought here: I think he's talking about the flexible version with
the stranded center conductor which like the LMR-400UF is a bit larger
than the solid center conductor. Although I've always been able to get
them to fit into the standard center pins, it sometimes takes a bit of
determination and care.<:-))
I've also noted an inconsistency in the crimp, Vs Clamp descriptions.
One supplier told me when I wanted crimp connectors with solder center
pins they were either one of the other, not a mix, but I have a number
of crimp connectors for LMR-600 that use center pins designed for
soldering complete with the small solder hole drilled in the side. OTOH
even if the center pin is designed for crimping it can be soldered.
Between the die sets I have for RG-8/LMR-400/9913/9913F I have both
0.100 and 0.128, plus the tiny ones meant for 8X and 58 type cables.
Steve Davis -Davis RF Co. wrote:
> Mark, One of my affiliates that does
> cable assembly/terminations indicates that the .128 is not a good die to
> use, unless you tin the ctr conductor and find it to be a tight fit after
> crimping. They tinn and then solder the center pin on. Finding the .116 die
> and tool handle is possible but they don't know a source, other than what
> Amphenol is recommending, quite expensive I'm sure. Given that you are not
> in "production" mode, taking the time to tin, crimp and solder is certainly
> a thorough way of obtaining a good electric/mechanical connection to either
> of these cables.
> I think (?) that you had a follow-up question, or that was somebody
> else... I will find that again later and answer it.
>
>
One possibility for those who really insist on crimping the center
conductor is to take a 0.100 die and "adjusting" it with a small file
to 0.116 which is only 0.016 larger...IE 16 thousandths of an inch
isn't much. OTOH they'd want to make sure the new die is properly
marked, or identified.
73
Roger (KI8RI)
> 73, Steve , K1PEK,
>
> DAVIS RF Co., Div. of Orion Wire Co., Inc.
>
> Wire, Cable, RF Connectors and wire aerial parts. LMR, Heliax, Eupen
>
> Commercial / Military / & Custom Cable Design
>
> tel: 978-369-1738 Fax: 978-369-3484
> www.DavisRF.com
>
>
>
> ----- Original Message -----
> From: "Steve Davis -Davis RF Co." <sdavis@davisrf.com>
> To: <towertalk@contesting.com>
> Cc: <mspencer12345@yahoo.ca>
> Sent: Sunday, January 04, 2009 1:26 AM
> Subject: Crimper for Belden 9913 - Response DAVIS RF Co.
>
>
>
>> Mark, Ctr. conductor size for 9913 and 9913F7 is .108", so spec'g the
>> .116 die makes sense. however, my crimper source indicates that their
>> .128" is the one to use for 9913. This may not be as odd as it sounds
>> because the Belden spec can vary to +- .010, and I doubt it is on the
>> minus side. At any rate, I am checking with a reliable source on Monday
>> to see if the .128 will do the job well, I suspect so as my mfr. source
>> for the crimper and die is a very good one. Will advise on Mon.
>>
>> 73, Steve , K1PEK,
>>
>> DAVIS RF Co., Div. of Orion Wire Co., Inc.
>>
>> Wire, Cable, RF Connectors and wire aerial parts. LMR, Heliax, Eupen
>>
>> Commercial / Military / & Custom Cable Design
>>
>> tel: 978-369-1738 Fax: 978-369-3484
>> www.DavisRF.com
>>
>>
>>
>> Date: Sat, 3 Jan 2009 18:00:20 -0800 (PST)
>> From: Mark Spencer <mspencer12345@yahoo.ca>
>> Subject: [TowerTalk] Crimper for Belden 9913
>> To: towertalk@contesting.com
>> Message-ID: <375680.81409.qm@web38802.mail.mud.yahoo.com>
>> Content-Type: text/plain; charset=iso-8859
>>
>>
>>
>>
>>
>>
>>> Sorry for a possibly off topic post, but I'm wondering if any one has any
>>> wisdom crimping N connectors onto Belden 9913F7 that they could share
>>> with me.??
>>>
>>> According to the Amphenol web site
>>> http://www.amphenolrf.com/pdf/283.pdf?the center pin for Amphenol 9913
>>> conectors needs to be crimped with a .116 inch die.?? I've looked high
>>> and low for a .116 inch die for my crimper and can't find one, I do have
>>> a .128 inch die and according to the RF parts web site that is the
>>> appropiate size for crimping 9913 center pins.??? (The crimp for the
>>> outer connector seems to be?a common .429 inch size.)
>>>
>>> Google searches for .116 inch dies and crimpers are not turning anything
>>> up either.
>>>
>>> I'm wondering if the amphenol connectors need a different size crimper
>>> than other common connectors ???? I've always had good results using
>>> amphenol brand connectors and would like to use them going forwards.
>>>
>>> I've seen several other crimpers advertised for crimping 9913 connectors
>>> but they don't specify the die sizes.? I'm reluctant to order one with
>>> out knowing what the die sizes are.
>>>
>>> Does any one have any practical experience they can share with me about
>>> crimping N connectors to Belden 9913F7 cable ??? I'd really like to use
>>> crimp style connectors going forwards but I want to make sure I crimp
>>> them properly.
>>>
>>> 73's
>>>
>>> Mark
>>> VE7AFZ
>>>
>>>
>>>
>>>
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
>
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|