Towertalk
[Top] [All Lists]

Re: [TowerTalk] M2 20M5 SWR

To: <john@kk9a.com>, <TOWERTALK@contesting.com>
Subject: Re: [TowerTalk] M2 20M5 SWR
From: "Jorge Diez - CX6VM" <cx6vm.jorge@adinet.com.uy>
Date: Thu, 31 Dec 2009 13:38:59 -0200
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
Hello,

I just returned to do some measurements.

I have right now installed my back up radio (TS450), with a Diamond SWR, a
Drake L7 amp and a WX0B sixpack

All the reports I read before, where from my swr meter in the TS450, that
displays many bars to up to 2.5-2.9:1 SWR.

But today I notice that is only when the sixpack is connected

I put the antenna direct to the radio and the SWR is 1.4:1 in 14000 and
1.8:1 in 14400 in both TS450 meter and Diamond SWR meter.

This also happens with my 15M6 antenna: with the antenna to the sixpack it
have in the TS450 meter a SWR of 2.5 in 21000 to 21400.  With the antenna
direct to the radio it have 1.2:1 from 21000 to 21300 in both TS450 meter
and Diamond SWR meter.

What´s wrong?

I change the loop that go from the Diamond SWR to the sixpack and is the
same, so the problem is not in this coaxial.

Any idea why with the antennas to the sixpack the radio meter display high
SWR? (here the Diamond display the 1.4:1 in 14000 so is only in the radio
meter this difference when antennas going to the sixpack)

I fully rotate the antenna and SWR was constant in all the 360 degrees (just
a little diference from 1.4:1 to 1.6:1 I think is not a problem)

Anyway in next days I will change the 20M5 to be in parallel with the XM510
antenna

Thanks!
Jorge
CX6VM



-----Mensaje original-----
De: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] En nombre de john@kk9a.com
Enviado el: Lunes, 28 de Diciembre de 2009 11:05 p.m.
Para: TOWERTALK@contesting.com
CC: cx6vm.jorge@adinet.com.uy
Asunto: Re: [TowerTalk] M2 20M5 SWR

Is the SWR OK higher in the band or bad all across.  If it is bad all over 
it is possible that the 10m boom is interacting.  I think that the Cushcraft

elements are not insulated making it difficult to guess if there is any boom

interaction without modeling the system. Why is the 10m antenna at 90 
degrees?  There should be little interaction if they are parallel and it is 
easier to operate the station when the rotators have the correct reading.

John KK9A also P40A


To: <TOWERTALK@contesting.com>
Subject: [TowerTalk] M2 20M5 SWR
From: "Jorge Diez - CX6VM"
Date: Sun, 27 Dec 2009 15:40:23 -0200
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>

Hello,



I installed a M2 antenna, 20M5 at 33 mts.  I assembly it for FULL BAND
dimensions



I have in the same tower a stack of three XM510 monobanders for 10 mts, the
top one is 3 mts over the 20M5 cross at 90 degrees from the 20M5.



At 14000 I have 2.9:1



This will be because of the other 10 mts antennas in the same tower?  Or at
FULL BAND the 20M5 have this swr at 14000?



Thanks!



73,

Jorge

CX6VM 

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
No virus found in this incoming message.
Checked by AVG - www.avg.com 
Version: 8.5.430 / Virus Database: 270.14.122/2590 - Release Date: 12/28/09
07:16:00

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>