Re: [TowerTalk] Al-to-Al

[Steve Bookout <steve@nr4m.com>]

I must agree with Tim on this.  This stuff has never let me down.
To make a bit easier to apply, and although it may be a 'sin', I apply 
it to the inner element, then spray WD-40 on it and spread it with vinyl 
gloved hand.
Goes on a bit more even this way.

73 de Steve, NR4M

On 2/13/2018 7:56:PM, Tim Duffy wrote:
> I used Penetrox for years - noticed that after 10 years or more that the
> Penetrox would dry out and turn to a crusty dust. I mentioned that to W3LPL.H
> Frank said try Jet Lube SS-30 - which is what he uses at his mega station
> for all of his antennas.
>
> I have been sold on Jet Lube SS-30 ever since. After 25 years here at K3LR -
> the Jet Lube SS-30 comes apart and is clean and offers a great low loss
> connection. I use it everywhere hardware and connections are involved (even
> in the shack) - as does W3LPL. Do not worry that this is copper based paste
> - it works SUPER for Al to Al.
>
> https://www.dxengineering.com/parts/jtl-12555
>
> 73
> Tim K3LR
>
> -----Original Message-----
> From: TowerTalk [mailto:towertalk-bounces@contesting.com] On Behalf Of Bob
> K6UJ
> Sent: Tuesday, February 13, 2018 6:45 PM
> To: Kim Elmore; towertalk@contesting.com
> Subject: Re: [TowerTalk] Al-to-Al
>
> Kim,
> You will get several suggestions on this.  I use Penetrox.  Used it on
> aluminum antenna element joints for years.  Does a great job of preventing
> corrosion and preserving the aluminum.  I have taken apart yagis that have
> been up for over 20 years and the exterior of the aluminum tubes were
> corroded, naturally, but the internal mating surfaces where the penetrox was
> used were shiny and bright, like new.  I first started using it years ago on
> KLM antennas, they provided a tube with their antennas, and still use it.DX
> engineering has it :https://www.dxengineering.com/parts/dxe-p8a
>
>
> BobK6UJ
>
>
>
>        From: Kim Elmore <cw_de_n5op@sbcglobal.net>
>   To: towertalk@contesting.com
>   Sent: Tuesday, February 13, 2018 2:09 PM
>   Subject: [TowerTalk] Al-to-Al
>     
> When assembling Al -to-Al junctions in an Antenna, what anti-corrosion
> compound should be used at the joints?
>
> Kim N5OP
>
> "People that make music together cannot be enemies, at least as long as the
> music lasts." -- Paul Hindemith
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
>
>     
> _______________________________________________
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk